Perles HB 6142-14LT Mode D'emploi page 4

�
�
c) Use only that battery in the power tool that is
intended for its use. The use of other batteries can
cause bodily injuries and fire.
d) When a battery is not used, it must not come into
contact with metal objects that would cause
bridging contacts: these are for ex. office
paperclips, coins, keys and other small metal
objects. A short circuit between the battery contacts
can cause burns or a fire.
e) Wrong use can cause the liquid to run out of the
battery. Avoid coming into contact with it. If you
accidentally do come into contact with it, wash the
affected spot with water. Should the battery liquid
splash into your eyes, you must seek for medical
assistance after rinsing with water. Battery liquid can
cause skin irritation or burns.
6) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
TECHNICAL DATA
Data
Voltage
No load speed 1
No load speed 2
Max. torque
Chuck
Automatic spindle lock
Max. drilling in steel
Max. drilling in concrete
Max. drilling in wood
Max. diameter of wood
screw
Max. diameter of metrical
screw
Charger type
Charging time
Li – ion battery
Battery capacity
Weight with battery
LpA (sound pressure
level) measured at user's
ear
LWA (sound power level)
Vibration level
Noise and Vibration
The measured values were defined according to EN
60745
Noise level at work can exceed 85 dB (A). Wear personal
ear protection.
Intended use
The tool is intended for screwing in and loosening of
screws, for drilling in wood, metal, ceramics and plastics.
�
�
navodilo_konèno.indd 4
�
�
Unit HB 6142-14LT HB 6182-14LT HB 7142-14LT
V 14
rpm 0-400
rpm 0-1400
Nm 35
mm 0,8-10
yes
mm 10
mm -
mm 15
mm 5
mm 6
type LT80B
h 1
type
Ah 1,4
kg 1,20
dB(A) 72,8
dB(A) 83,8
2
m/s <2,5
4
DESCRIPTION
1 Battery
2 Battery lock button
3. ON/OFF switch
4 Rotation direction switch
5 Mechanical speed switch
6 Torque setting ring
7 Chuck
8 Charger
9 Charger control light
FOR OWN SAFETY
Before using the tool
Read the operating instructions
instructions carefully and follow them strictly.
- Check the battery tool and the battery before each
use. Do not use a damaged tool. Do not dismantle
the tool by yourself! Have it repaired by a service
center.
- Do not overload the tool so much that it comes to a
standstill. Switch it off immediately in case it gets
blocked.
18 14
0-420 0-400
0-1500 0-1400
40 25
0,8-10 0,8-10
yes no
10 10
- -
25 19
6 5
8 6
LT80B LT80B
2 1
1,4 1,4
1,25 1,40
72,8 72,8
83,8 83,8
<2,5 <2,5
- Hold the tool firmly while working. Provide for an
adequate longitudinal force in order to prevent the
screwdriver bit from slipping.
- Secure the workpiece.
corresponding clamping device.
- Children are not allowed to use the tool.
- Use original additional accessories that are
intended for this tool.
- Hold the tool firmly while working. High reaction
moment could appear when it is hard to drive in the
screw, there is a danger that a long screw will slip,
therefore use the auxiliary handle.
- Check if the battery is firmly fixed in the tool's
handle before you start working with the tool.
�
�
�
�
and safety
HB 7182-28LT
18
0-420
0-1500
30
0,8-10
no
10
-
29
6
8
LT80B
2
2,8
1,50
72,8
83,8
<2,5
Use a vice or a
�
17.8.2011 14:21:52