Publicité
Les langues disponibles
Les langues disponibles
OPERATION MODE
Sequence Number
1
2
3
4
5
6
7
8
9
10
11
* Multi Mode produces random colors and flashing patterns.
** Color Wheel Mode is the smooth color-changing pattern from aqua,
to blue, to purple, to red, to orange, to yellow, to green, then back to
aqua and repeat. The Standard mode gradually changes through all the
colors every 30 seconds. The Slow mode takes 6 minutes to cycle through
all the colors before repeating, and the Slowest mode takes 2 hours for
each pass through the colors.
For the Color Wheel Modes, there is a visual indication of which mode
you are in. For the Slowest mode, the blue LEDs will flash 3 times before
starting the initial gradual changing from aqua. For the Slow mode, the
green LEDs will flash 3 times before going to aqua and transitioning
through the color wheel. The LEDs flash only on the initial startup; the
LEDs will not flash on subsequent cycles of the color wheel. The Standard
Color Wheel Mode does not flash at all, but starts transitioning in color
from aqua through its cycle.
Selecting Operation Mode
Setting programs is determined by how long the power is removed
before restarting. To switch modes, simply turn the power switch off
for 1/2 to 4 seconds, then back on to advance to the next state. If the
on/off switch is left in the OFF position for 4 to 8 seconds, the LED lights
will resynchronize when powered up by flashing red three times,
at which point all of the lights in the system will initialize in the
same state (Mode 1, Red). If multiple lights are installed, the modes will
synchronize together after this synch reset.
The LED lights have a memory that when switched off for more than
8 seconds, all the lights will power up in the last state they were in
when powered down. This allows users to leave lights in a favorite mode
without having to search for it when powering up the light. If the unit
is turned off during modes 10 or 11, and the power is off longer than
8 seconds (color/mode memory state), the Mode Indicator Flash will
reactivate immediately upon power up. This a visual reminder to you of
which mode is running.
Color/Function
Red
Yellow
Green
Aqua
Blue
Purple
White
Multi Mode*
Color Wheel - Standard**
Color Wheel - Slow**
Color Wheel - Slowest**
SERVICE INSTRUCTIONS
WARNING
MAKE CERTAIN THAT THE UNIT IS DISCONNECTED FROM THE POWER
SOURCE BEFORE ATTEMPTING TO SERVICE OR REMOVE ANY COMPONENT!
1. Do not remove the cord strain relief (hex nut). This will damage the
seal and result in possible leakage.
Bulb Replacement
NOTE: No tools are required to service the light.
1. Unscrew the outer ring by turning it counterclockwise. Next, remove
the lens and O-ring.
2. CAUTION: The bulb and plastic bulb holder are one piece.
DO NOT pull on the bulb itself. Pull only on the plastic bulb holder.
3. To install bulb, simply plug the bulb into the socket (as shown in
Figure 1). Ensure that the two pins of the bulb are well-seated in
the two small inner holes of the socket. DO NOT touch the new bulb.
Only touch the plastic bulb holder. Touching the bulb may shorten
bulb life. As you push the bulb assembly down into the light housing,
twist the bulb assembly so that the openings in the plastic bulb
holder are oriented with the ribs on the inside of the light housing.
4. Make sure the O-ring and sealing surfaces are clean and in
good shape. Reinstall the O-ring and lens.
5. Reinstall the outer ring. DO NOT use any tools. Tighten the outer
ring until the tab on the light ring touches the mounting rib on the
lamp housing.
CAUTION: MAKE CERTAIN NO WATER OR MOISTURE IS INSIDE LAMP
PRIOR TO REASSEMBLING.
Cleaning
The lens will require periodic cleaning. Simply wipe the outside of the
lens with soft cloth. DO NOT use abrasives. This may damage the lens.
CAUTION: If the lamp is disassembled for cleaning, be certain
that the lamp housing is not submerged in water. This will allow water to
enter the cord, which could result in an electrical hazard.
ENGLISH EN
3
Publicité
