Instructions For Use; Placement Tool; Assembly; Electrical Connection - stayer SD27BE Instructions D'emploi

Safety warnings specific for wire brushing operations
- Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress
the wires by applying excessive load to the brush.
The wire bristles can easily penetrate light clothing
and/or skin.
- Allow brushes to run at operating speed for at least
one minute before using them. During this time no
one is to stand in front or in line with the brush.
Loose bristles or wires will be discharged during the
run-in time.
- Direct the discharge of the spinning wire brush
away from you. Small particles and tiny wire fragments
may be discharged at high velocity during the use of
these brushes and may become imbedded in your skin.
Additional safety warnings
Wear safety goggles.
- Use suitable detectors to determine if utility lines
are hidden in the work area or call the local utility
company for assistance. Contact with electric lines
can lead to fire and electric shock. Damaging a gas line
can lead to explosion. Penetrating a water line causes
property damage or may cause an electric shock.
- Release the On/Off switch and set it to the off
position when the power supply is interrupted, e.
g., in case of a power failure or when the mains
plug is pulled. This prevents uncontrolled restarting.
- Secure the workpiece. A workpiece clamped with cla
ping devices or in a vice is held more secure than by
hand.

3.Instructions for use

3.1 Placement Tool

Read all safety warnings and all instructions.
Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious
injury. While reading the operating instructions,
unfold the graphics page for the machine and
leave it open.

3.2 Assembly

Before any work on the machine itself, pull the mains
plug.
Mounting the Grinding Tools (see figure A)
Only use properly fitting and undamaged
openend spanners.
– Clean the grinder spindle 3 and all parts to be mounted.
– Hold the grinder spindle 3 with spanner 8 by the spanner
flats.
Loosen the clamping nut 2 with spanner 8 by applying it to
the spanner flats and turning in anticlockwise direction.
ENGLISH
17
– Insert the clamping shaft of the grinding tool to the stop
into the collet chuck 1.
– Hold the grinder spindle 3 firmly with spanner 8 and
clamp the tool bit with spanner 8 by the spanner flats,
turning in clockwise direction.
The grinding tools must run completely concentrical. Do
not continue to use out-of-round grinding accessories, ins
tead, replace before continuing to work.
Do not tighten the collet chuck of the clamping nut as
long as no grinding accessory is mounted. Otherwise,
the collet chuck can become damaged.
Dust/Chip Extraction
Dusts from materials such as lead-containing
coatings, some wood types, minerals and metal
can be harmful to one's health. Touching or breathing
in the dusts can ca se allergic reactions and/or lead to
respiratory infections of the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-trea
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Prevent dust accumulation at the workplace. Dusts
can easily ignite.

3.3 Electrical connection

Observe correct mains voltage! The voltage of
the power source must agree with the voltage
specified on the nameplate of the machine.
Power tools marked with 230 V can also be operated
with 220 V.

3.4 Illustrated description

1 Collet chuck
2 Clamping nut
3 Grinder spindle
4 Spindle collar
5 On/Off switch
6 Thumbwheel for speed preselection
7 Handle (insulated gripping surface)
8 Spanner service

4. Operating instructions

4.1 Placement and testing

4.1.1 Model SD27BE
Switching On and Off
To start the power tool, push the On/Off switch 5 forwards.
To lock the On/Off switch 5, press the On/Off switch 5
down at the front until it latches.
17