Troubleshooting - COMAC CM Mini Orbital Manuel D'utilisation Et D'entretien

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 29
In this chapter, the most common problems of use of this device are outlined. If the problems are not resolved with the following information, please
contact the authorized centre nearest your area
PROBLEM
The switch is not in the On "1" position
The device does not
start
Battery is not correctly inserted in the battery support
compartment
Battery is discharged
The cables between the battery support compartment and
machine base are not correctly connected
The battery does not
Battery has not been correctly positioned inside the battery
charge.
charger compartment
The plug of the battery charger has not been correctly
inserted in the recharger unit, or into the electrical outlet
Battery has reached the end of its lifespan
The battery has a short
The battery has not been completely recharged, and
run time
therefore does not provide the acceptable runtime
The battery has expired and has reached the end of its
lifespan
One of the blue leds
The machine is equipped with a system of control of
flashes for a few
electrical absorption. If this value exceeds a certain limit
seconds and then the
for a time period of more than 8 seconds, the machine
machine turns off
stops and the warning LED flashes red, alternating with the
flashing blue LED of the machine ON indicator
The machine vibrates
Loosening of the screws on the vibrating pad driver plate
excessively and emits
a strange noise
Breakage of an elastic element under the vibrating plate
The machine does not
The cleaning pad is used up
clean properly
The pad does not
The limit of use of the cleaning pad has been surpassed
remain attached to the
and it can no longer cling to the vibrating plate
vibrating plate
comply with the requirements of the following Directives:
The person authorized to compile the technical file:
Sig. Giancarlo Ruffo
Via Maestri del Lavoro, 13
37059 Santa Maria di Zevio (VR) Italy
PRODUCTION YEAR 2021
TROUBLE SHOOTING
POSSIBLE CAUSE
EC DECLARATION OF CONFORMITY
37059 Santa Maria di Zevio (VR) Italy
declares under its sole responsibility that the products
MACHINE:SINGLE DISC mod.CM ORBITAL MINI B
2006/42/CE: Direttiva macchine.
2014/35/CE: Direttiva bassa tensione.
2014/30/CE: Direttiva compatibilità elettromagnetica.
2011/65/UE : RoHS
Press on the ON/OFF switch
Press fully the battery, sliding it inside the battery support compartment
until you sense its correct coupling at the end
Charge battery using the proper battery charger supplied with the
machine
Check the cables, ensuring the correct tightening of the electrical
connections in the lower part of the battery support compartment
Extract the battery and re-insert it again inside the battery charger
compartment until you hear the special coupling sound, and check that
the LED signals indicating the start of recharging are illuminated (fixed
green light situated on the recharge unit)
Reposition the plug in the battery recharge unit and/or check the
correct insertion of the battery recharger plug into the electrical outlet
Replace the battery with a new one
Recharge the battery using the specific battery charge supplied with
the machine, for a recharge time of at least 3 hours, to completely
restore the charge performance
Replace the battery with a new one.
Turn off the machine. After a few seconds (time varies depending on
operating conditions), and then re-start he machine and continue work
Check and if needed, tighten the screws which attach the drive plate
onto the orbiting / vibrating group
Contact an authorized service center to replace the damaged element
Replace the pad with a new one, suitable for the work being carried out
Replace the pad with a new one, suitable for the work being carried out
La sottoscritta ditta fabbricante:
COMAC S.p.a.
Via Maestri del Lavoro, 13
28
SOLUTION
COMAC S.p.a.
Legal representative
Giancarlo Ruffo

Publicité

Table des Matières
loading

Table des Matières