TFA 30.1034 Manuel D'instructions page 2

TFA_No. 30.1034_Anl_D_GB_06_18
LCD
➀
Digital control thermometer
Thank you for choosing this instrument from TFA.
1. Before you use this product
• Please make sure you read the instruction manual carefully.
• Following and respecting the instructions in your manual will prevent damage to
your instrument and loss of your statutory rights arising from defects due to inco-
rrect use.
• Likewise, we take no responsibility for any incorrect readings or for any consequen-
ces resulting from them.
• We shall not be liable for any damage occurring as a result of non following of
these instructions.
• Please take particular note of the safety advice!
• Please keep this instruction manual safe for future reference.
2. Field of operation
• Temperature measurement with waterproof cable sensor for food (in accordance with
HACCP and EN13485), handcraft, laboratories, industry, agriculture and hobbies.
3. For your safety
• This product is exclusively intended for the field of application described above. It
should only be used as described within these instructions.
• Unauthorised repairs, modifications or changes to the product are prohibited.
Caution!
Risk of injury:
• Keep this instrument and the battery out of reach of children.
• Batteries contain harmful acids and may be hazardous if swallowed. If a battery is
swallowed, this can lead to serious internal burns and death within two hours. If you
suspect a battery could have been swallowed or otherwise caught in the body, seek
medical help immediately.
• Batteries must not be thrown into a fire, short-circuited, taken apart or recharged. Risk
of explosion!
• Low batteries should be changed as soon as possible to prevent damage caused by
leaking.
• Wear chemical-resistant protective gloves and safety glasses when handling leaking
batteries.
Important information on product safety!
• Do not place the unit near extreme temperatures, vibrations or shocks.
• Only the probe is heat resistant up to 70 °C.
• Do not immerse the display unit into water. Water can penetrate and cause malfunc-
tion.
4. Components
Display (LCD)
1
Battery low
2
Alarm symbol
3
Buzzer Alarm Flashing Icon
5. Installation
• Remove the protective foil from the display. Open the battery cover on the backside of
the instrument by opening the two little screws next to the magnet by a screw driver,
remove the insulation strip and tighten the cover again. The unit is now ready for use.
6. Operation
6.1 Temperature indication
• The present temperature in °C or °F measured by the cable sensor is indicated on the
display. Press the +1-switch to change from °C to °F readout.
6.2 ON/OFF button
• Press the "ON/OFF"-button to switch the instrument on and off. Settings are preserved,
for measurements and alerting the instrument must be switched on.
6.3 Hold/max-min-function
• When pressing the "MAX/MIN"-button, the present display is held (HOLD).
• Pressing again the "MAX/MIN"-button, the display shows the maximum temperature
since the last reset (MAX).
• When pressing the "MAX/MIN"-button again, the display shows the minimum temper-
ature since the last reset (MIN).
• To go back to the present temperature display, press the "MAX/MIN"-button once
more.
• To reset the maximum and minimum values, hold the "MAX/MIN"-button for 3 sec-
onds, while MAX or MIN is indicated ( ---).
6.4 Upper limit and lower limit temperature alert
• To set an upper temperature limit, that means when passing the temperature an alarm
is beeping, press the "AL SET"-button in normal mode. The upper temperature limit
is shown and it is flashing. Set the desired temperature by pressing the +1-button.
Hold and press the button for a fast count. Now you can activate (alarm symbol
appears) or deactivate (alarm symbol disappears) the alarm pressing "MAX/MIN"- but-
ton. Confirm by pressing the "AL SET"-button.
13.06.2018 10:29 Uhr Seite 2
➁
4
Higher Alarm
5
Lower Alarm
Bedienungsanleitung
Instruction manual
➂
➃
➄
Digital control thermometer
• The lower temperature limit
limit, that means when falling below the temperature an alarm is beeping, press +1-
button. Hold and press the button for a fast count. Now you can activate or deactivate
the alarm pressing "MAX/MIN-button". Confirm by pressing the "AL SET"-button.
• After setting temperature alarm the symbols
ture alarm is acti-vated.
• When passing or falling below the selected temperature limit an alarm signal will
sound for 1 minute, the buzzer alarm icon and the corresponding arrow
flash. The alarm and the buzzer alarm icon can be turned off manually by pressing any
button.
• When temperature is again within the selected limits the alarm signal will stop (within
1 min.) and the buzzer alarm flashing icon disappears. The arrow keeps on flashing
showing that the temperature was higher/lower than the preset value at least once in
the past. Press +1- button and the arrow will stop flashing.
7. Care and maintenance
• Clean the device with a soft damp cloth. Do not use solvents or scouring agents.
• Remove the battery if the device will not be used for an extended period of time.
• Store the instrument in a dry place.
8. Battery replacement
• For a long battery life, it is recommend to press the "ON/OFF" button to switch the
instrument off when not in use.
• When the battery is used up, the low battery icon appears.
• Open the battery cover on the backside of the instrument, insert a new battery CR2032
3V Lithium and tighten the cover again.
9. Troubleshooting
Problems
No display
Incorrect display
10. Waste disposal
This product has been manufactured using high-grade materials and components which
can be recycled and reused.
Never dispose of empty batteries and rechargeable batteries in ordinary
household waste.
As a consumer, you are required by law to take them to your retail store or
to an appropriate collection site depending on national or local regulations
in order to protect the environment.
The symbols for the heavy metals contained are:
Cd=cadmium, Hg=mercury, Pb=lead.
This product is labelled in accordance with the EU Waste Electrical and
Electronic Equipment Directive (WEEE).
Please do not dispose of this product in ordinary household waste. As a
consumer, you are required to take end-of-life devices to a designated col-
lection point for the disposal of electrical and electronic equipment, in
order to ensure environmentally-compatible disposal.
11. Specifications
Measuring range temperature:
Precision:
Cable:
Resolution:
Protection class:
Power consumption:
Housing dimension:
Weight:
This product fulfills the guidelines according to EN 13485.
Suitability: S, T (Stockage, Transport)
Location: A
Accuracy class: 1
Measuring range: -40°C...+70C
In accordance with EN 13485, this instrument is subject to regular inspections as per
EN 13486 (recommendation: yearly).
TFA Dostmann GmbH & Co. KG, Zum Ottersberg 12, D-97877 Wertheim, Germany
No part of this manual may be reproduced without written consent of TFA Dostmann.
▲
The technical data are correct at the time of going to print and may change without prior notice.
The latest technical data and information about your product can be found by entering the
product number on our homepage.
www.tfa-dostmann.de
06/18
Cat.-No. 30.1034
▼
is shown and it is flashing. To set a lower temperature
▲▼
show, if an upper or lower tempera-
Solutions
➜ Ensure battery polarity is correct (+ pole above)
➜ Change the battery
➜ Switch on the instrument (ON)
➜ Check the position of the cable sensor
➜ Change the battery
-40°C ...+70°C (-40°F...+158°F)
±0.5°C @ -20...+25°C,
otherwise ±1°C
approx. 3m
0.1°C
IP 65
1x CR2032 3V Lithium Button cell battery (included)
87 x 17 (29) x 52 (57) mm
79 g (device only)
▲ ▼
or will
RoHS