Black & Decker BDCDS12 Traduction Des Instructions Initiales page 4

ENGLISH
Slippery handles and grasping surfaces do not allow for
safe handling and control of the tool in unexpected
situasions.
5. Battery tool use and care
a. Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with
another battery pack.
b. Use power tools only with specifically designated
battery packs. Use of any other battery packs may create
a risk of injury and fire.
c. When battery pack is not in use, keep it away from
other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can
make a connection from one terminal to another.
Shorting the battery terminals together may cause burns
or a fire.
d. Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally
occurs, flush with water. If liquid contacts eyes,
additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
e. Maintain powertools and accessories. Check for
misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the
power tools operation. If damaged, have the power
tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
6. service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
Additional power tool safety warnings @
Warning! Additional safety warnings for sanders
@
Warning! Contact with or inhalation of dusts
arising from sanding applications may endanger
the health of the operator and possible bystand-
ers. Wear a dust mask specifically designed for
protection against dust and fumes and ensure
that persons within or entering the work area are
also protected.
4
(Original instructions)
Hold power tool by insulated gripping surfaces when
u
performing an operation where the sanding accessory
may contact hidden wiring. Accessory contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
Use clamps or another practical way to secure and
u
support the workpiece to a stable platform. Holding the
work by hand or against your body leaves it unstable and
@ may lead to loss of control.
Warning! Take special care when sanding some
woods (e.g. beech, oak) and metal which may
produce toxic dust. Wear a dust mask specifi-
cally designed for protection against toxic dust
and fumes and ensure that persons within or
entering the work area are also protected.
@
Warning! Use this tool in a well ventilated area
when sanding ferrous metals. Do not operate
the tool near flammable liquids, gases or dust.
Sparks or hot particles from sanding or arcing
@
motor brushes may ignite combustible materials.
Warning! Do not sand magnesium! There is a
risk of fire or explosions.
Thoroughly remove all dust after sanding.
u
The intended use is described in this instruction manual.
u
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual may present a risk of
personal injury and/or damage to property.
Safety when sanding paint
@
Warning! Observe the applicable regulations
for sanding paint. Pay special attention to the
following:
Whenever possible, use a vacuum extractor for dust col-
u
lection.
Take special care when sanding paint which is possibly
u
lead based and may produce toxic dust:
Do not let children or pregnant women enter the work
u
area.
All persons entering the work area should wear a mask
u
specially designed for protection against lead paint dust
and fumes.
Do not eat, drink or smoke in the work area.
u
Dispose of dust particles and any other removal debris
u
safely.
Safety of others
This appliance is not intended for use by persons (includ-
u
ing children) with reduced physical, sensory or mental