Monacor INC-4000BX Manuel D'utilisation page 5

INC-4000 BX
Order No. 18.0127
ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS
When a connection to the camera has been established, the view with the cur-
rent camera image (fig. 3) will be displayed. The following options are available:
a
View "Live Video" with display of camera image
b
View "Playback" to replay the recordings from the camera
c
View "Configuration" to change the camera settings
d
Button to change the password
e
Button to log out
f
Camera image with information on the stream currently transmitted
g
Toolbar with the following functions:
: PTZ window to control a pan/tilt head via RS-485
 / : Stop / Start of image transmission
"Stream": Selection of a stream
: Activation / Deactivation of audio transmission from the camera and selec-
tion of audio input (15):
: Activation / Deactivation of audio transmission to the camera
[AUDIO OUT (14)]
: Specific camera settings (e. g. brightness control, mirror image)
: Snapshot function to save a snapshot as an image file
: Starting / Stopping a video recording on the PC
: Activation / Deactivation of image analysis functions ("Intelligent Analysis")
When the camera image is clicked with the right mouse button, the following
menu will appear:
Menu item
full-screen image (exit)
Full Screen (Exit Full Screen)
alternatively: double-click the image
Sensor like
zooming in / zooming out
Zoom In / Out alternatively: use the scroll wheel to zoom in / out or drag the
mouse to select the desired image section
Restore Panorama display of the entire image (after zooming in)
To change the settings for the camera, select the tab
☞
"Configuration" ( fig. 4). On the left (
the settings. To show additional subcategories, click ⊞. To set, for example, the
current time for the camera, go to "Device  Date and Time".
To save a setting that has been changed, click the green check mark ✔ or the
button "Apply". To load the current settings from the camera, click the button
"Refresh".
6.1 Sensor menu
To activate the sensor menu (fig. 5), click the icon
➄
Sensor menu
Select the mode in the list field at the bottom on the left. To change the settings,
select "Debug Mode". The settings made in the sensor menu can be saved with
"Save" (Schemes 1 – 4) and retrieved (selection via second list field). It is possible
to define an individual validity period for each of the settings saved (view "Time
Segment"). This will allow you, for example, to make different settings for day
and night.
To reset the settings to the values saved, click "Reset". To reset the settings to
the factory settings, click "Factory Setting".
ELECTRONICS FOR SPECIALISTS
A ⁄ B
Function
c
and go to the view
h
), select the desired category for
.
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright by MONACOR INTERNATIONAL. All rights reserved.
©
ELECTRONICS FOR SPECIALISTS ELECTRONICS FOR SPECIALISTS
The setup options of the sensor menu can be found in the table below.
View
Enable
Time Segment
Start Time
End Time
Brightness
Saturation
Image
Sharpness
Contrast
Scene
Aisle
Scene
Mirror
Exposure Shutter, Gain, Iris
WB Mode, Red, Blue
Day Night Mode
Noise Reduction 2D NR, 3D NR
WDR, HLC, BLC,
Enhance Image
Anti-Shake, Defog
7 Resetting the Camera
When the camera is reset to its factory settings, any changes the user has made
to the camera settings will be lost. Keep the button RESET FACTORY (12) pressed
for more than 5 seconds. The camera will be restarted* and reset to the static
IP address 192.168.0.120. The default user name and the password for log-in
is: admin.
* Note: Starting the camera may take a few minutes.
8 Specifications
Image sensor: . . . . . . . . . . .CMOS, 8.5 mm (1⁄3 ")
Minimum illumination: . . . .0.01 lx
Resolution: . . . . . . . . . . . . .30 frames max. per second
Electronic shutter: . . . . . . . .1⁄5 – 1/20 000 s
Protocols: . . . . . . . . . . . . . .IPv4, IPv6, HTTPS, RTSP, DDNS, SMTP, SSL,
Compression: . . . . . . . . . . .MPEG-4 H.264 / H.265, MJPEG
Video streaming: . . . . . . . . .Mainstream 500 – 12 000 kbit /s
Network: . . . . . . . . . . . . . .Ethernet 10 / 100 Mbit / s
Ambient temperature: . . . .−10 °C to +50 °C
Power supply: . . . . . . . . . . . ⎓ 12 V/ 300 mA or
Dimensions (W × H × D): . .78 × 65 × 142 mm
Weight: . . . . . . . . . . . . . . .405 g
ELECTRONICS FOR SPECIALISTS
Setting Function
activation of the validity period defined for these
settings (Scheme)
start of validity period
end of validity period
brightness
saturation
sharpness
contrast
place of application
aisle mode
mirror image: off, horizontal, vertical, horizontal
and vertical
exposure settings
white balance
day/ night switching
noise reduction
image enhancement
with 2592 × 1520 pixels
ONVIF 2.6 etc.
Substream 100 – 6000 kbit /s
∿
24 V/ 150 mA
or PoE IEEE 802.3af
Subject to technical modification.
A-1988.99.01.05.2019
ELECTRONICS