Videx 4000 Serie Instructions D'installation page 2

4000 Series
Art. 4042 .. 4045
Art. 4042D .. 4045D
POWER SUPPLY
To give power supply to the module
connect one of the inbuilt IDC male
connector to the IDC male connector
I
of the camera unit module through the
flat cable provided. A further buttons
expansion module can be connected to
the free IDC male connector of the pre-
vious expansion module (Fig. 3).
Made in Italy
PUSH BUTTONS CONFIGURATION
MAX VALUES FOR ART:
4045
40 35 30 25 20 15 10 5
4044
39 34 29 24 19 14 9 4
4043
38 33 28 23 18 13 8 3
4042
37 32 27 22 17 12 7 2
36 31 26 21 16 11 6 1
L
SW1 SETTINGS
Left position = TRADE RIGHT
SIDE
Trade button connection related to push button
no.1 (only if SW1 is swithed on Trade side).
SW1
STANDARD
J2 AND J1 BACKLIT LEDS SETTINGS
DEFAULT SETTING
TRADE
J2
P1 EXPANSION BUTTONS
B A
USING WITH ART. 4384, 4384X, 4304, 4304X AND ONE SINGLE
EXPANSION BUTTON MODULE
J2
B A
HOW TO REMOVE/INSERT THE CARD NAME HOLDER
• To avoid damage to the module front plate, mask the side that
will be in contact with the screwdriver blade;
• Insert the screwdriver (flat side) into the card-holder hole as
shown in Fig. 4;
• Move the screwdriver to the left as shown in Fig. 5 to extract
the card name holder;
• Edit the card name then replace it inside the holder and refit:
insert the holder inside its housing from the left or right side
then push the other side until it clips into place.
Art. 4042 .. 4045 - Art. 4042D .. 4045D- Installation instructions
Single row button expansion modules
Double row button expansion modules
Art. CFL17
17 cm lenght flat cable
(Supplied)
4045D STEEL
Art. CFL45
4044D ALI
45 cm lenght flat cable
4043D HIGH BRASS
(to be ordered separately)
4042D MATTE
Fig. 3
LEFT
SIDE
5+n
4+n
3+n
2+n
1+n
R
B A
J2
J1
EXPANSION BUTTONS
B A
J1
B A
PUSH BUTTONS CONFIGURATION
MAX VALUES FOR ART:
40 35 30
39 34 29
38 33 28
37 32 27
36 31 26
B A SW1
J1
USING WITH ART. 4384, 4384X, 4304, 4304X AND A COUPLE
TRADE
EXPANSION BUTTON MODULES
P1
Art. 4384, 4384X, 4304, 4304X
Expansion button module 1
J2
B A
Expansion button module 2
J2
B A
NOTE: to connect more than 2 expansion button modules,
please refer also to the installation diagrams.
Fig. 4
- 2 -
OR
Made in Italy
4045 4045D
25 20 15 10 5
4044 4044D
24 19 14 9 4
4043 4043D
23 18 13 8 3
4042 4042D
22 17 12 7 2
21 16 11 6 1
L
5+n
4+n
3+n
Right position = STANDARD RIGHT
2+n
SIDE
Standard matrix call buttons (default).
1+n
R
STANDARD
EXPANSION BUTTONS
J1
B A
J1
B A
Fig. 5
STEEL
ALI
HIGH BRASS
MATTE
LEFT
SIDE
B A B A
J2 J1
EXPANSION BUTTONS
1
2
66250255 - V4.3 - 15/01/22