Casals FC14 Notice Originale page 7

English
Hinge Router
FC14
Dear Customer,
Many thanks for trusting to Casals Professional.
Thanks to its continuous effort, our innovation and the
strictest quality controls, Casals Professional develops
electric Power Tools for the toughest jobs.
General Power Tools Safety Warning
WARNING Read all safety warnings and
all instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury
Save all warnings and instructions for future
reference
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool
Work Area Safety
- Keep work area clean and well lit. Cluttered or
dark areas invite accidents
- Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes
- Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control
- Ensure that neither the air access nor exit become
either totally or partially covered by drapery, clothing,
etc., as this increases the risk of fire.
Electrical safety
- Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock
- Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges or
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded
- Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
the risk of electric shock
- Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock
- When operating the power tool outdoors, use
an extension cord suitable for outdoor use. Use
a cord suitable for outdoor use reduces the risk of
electric shock
- If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock
- If any of the appliance casings breaks, immediately
disconnect the appliance from the mains to prevent
the possibility of an electric shock.
- Do not use the appliance if it has fallen on the floor, if
there are visible signs of damage or if it has a leak.
- Do not use the appliance with damp hands or feet, or
when barefooted.
- Do not use the appliance if the cable or plug is
damaged.
- Ensure that the voltage indicated on the rating label
matches the mains voltage before plugging in the
appliance.
- Do not touch the plug with wet hands.
Personal safety
- Stay alert, Watch you are doing and use common
sense when operating a power tool. Do not use
a power tool while you are tired or under the
influence of drugs, alcohol or medication. A
moment of inattention while operating power tools
may result in serious personal injury
- Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriated conditions will reduce
personal injuries
- Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
the power source and/or battery pack, picking up
or carrying the tool. Carrying power tools with your
finger on the switch or energizing power tools that
have the switch on invites accidents
- Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury
- Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations
- Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts
- If devices are provided for the connection of dust
ORIGINAL instructions
7