Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
PAGE 6
ENGLISH
Section 3. Installing Jandy Pro Series
Pro Series Light Fixture
during New Construction
WARNING
Risk of Electrical Shock or Electrocution.
This underwater light must be installed by a
licensed or certified electrician or a qualified pool
or spa serviceman in accordance with the National
Electrical Code
(NEC
®
®
Electrical Code in Canada, and all applicable local
codes and ordinances. Improper installation will
create an electrical hazard, which could result
in death or serious injury to pool or spa users,
installers or others due to electrical shock, and may
also cause damage to property.
Always disconnect the power to the pool or spa
light at the circuit breaker before servicing the light.
Failure to do so could result in death or serious
injury to serviceman, pool or spa users or others due
to electrical shock.
3.1
Preparing the Light Fixture for
Installation
NOTE The electrician must complete preparatory steps
before light fixture is installed; see Figure 1 (or
Figure 2, for spa).
Ensure that the pool or spa meets the requirements of
the current National Electrical Code (NEC) in the US,
the Canadian Electrical Code (CEC) in Canada, and all
applicable local codes and ordinances. A licensed or
certified electrician must install the electrical system
to meet or exceed those requirements before the
underwater light is installed. Some of the requirements
of the National Electrical Code, which the pool or spa's
electrical systems must meet, are as follows:
1.
The lighting circuit must have a Ground Fault
Circuit Interrupter (GFCI) for line voltage 120
volt models, and must have an appropriately rated
circuit breaker.
2.
The Junction Box (or, for 12 volt models, the
low voltage transformer) must be located at least
eight (8) inches above water level, at least four (4)
inches above ground level or pool deck level, and
at least four (4) feet from the edge of the pool or
spa; see Figure 1 for pools and Figure 2 for spas.
3.
The light fixture and all metal items within five (5)
feet of the pool or spa must be properly electrically
bonded to a reliable point of grounding.
Jandy
Pro Series Underwater Pool and Spa White Lights | Installation Manual
®
) in the US, the Canadian
4.
The wet niche must be properly installed so that
the top edge of the underwater light's lens is at
least 18 inches below the surface of the water in
the pool or spa; see Figure 1 or 2.
5.
The wet niche must be properly electrically
bonded and grounded via the No. 8 AWG ground
connector located at the rear of the niche; see
Figure 1 or 2.
NOTE The pool or spa electrical system can be
verified with a Pool and Spa Electrical
Qualification Test kit. The test kit is available
from local distribution. The electrical system
inspection using this kit must be performed by
trained and certified personnel.
To be certain that the pool or spa's electrical
system meets all applicable requirements, the
electrician should also consult the local building
department.
To GFCI, Circuit
Breaker and
Power Source.
48"
min.
4" min.
Rigid
Conduit
#8 AWG Ground
Connector bonded
Figure 1. Jandy Pro Series Pool White Light
Installation
To GFCI, Circuit
Breaker and
Power Source.
48"
min.
4" min.
Rigid
Conduit
#8 AWG Ground
Connector bonded
to rebar.
Figure 2. Jandy Pro Series Spa White Light
Installation
8" min. Junction Box or Low
Voltage Transformer, to the
max water level of the pool.
18" min. to top of Lens.
Concrete must be cut
back around Niche to
allow for a compacted
plaster seal.
11.50"
Coil 4 ft. of light cable
around Fixture.
16"
8" min. Junction Box or
Low Voltage Transformer.
18" min. to top of Lens.
Concrete must be cut
back around Niche to
6.0"
allow for a compacted
plaster seal.
Coil 4 ft. of light cable
around Fixture.
Publicité
Chapitres
Table des Matières
