Black & Decker DVB315JP Mode D'emploi page 6

ENGLISH
Only use with charger S003AQ-15 / SSC-
S003AQ-15 / SSC-150015XX
150015XX
Features
This tool includes some or all of the following features.
1. On/off power switch
2. Dust chamber release button
3. Dust chamber
4. Pet head attachment
5. Charger
6. Wall attachment
Use
Fitting the wall bracket (Fig. A)
Fit the wall bracket (6) to a suitable wall (preferably near a
u
power outlet) using the screws provided.
The unit can then be stored, when not in use, or during the
u
charging procedure, utilising the hanging attachment (6a).
Charging (Fig. B, C)
Place the charger (5) into the charging port (5a) on the
u
handle of the unit as shown in figure B.
Place the charging plug into a power outlet and switch on
u
as shown in figure C.
Attaching the pet head (Fig. D)
Warning! The unit needs to be switched off when the pet
head is attached or detached.
Warning! Do not use directly on pets.
Slide the dust bowl opening (3) into the opening of the
u
motorized pet head (4), ensuring that the connectors (4b)
engage with the recesses (3b). An audible click will be
heard.
Removing the pet head (Fig. D)
Pull the motorized pet head release tabs (4a) outward to
u
release them from the recesses (3a).
Pull the main unit from the pet head.
u
Warning! The unit needs to be switched off when the pet
head is attached or detached.
Switching on and off (Fig. E)
Push the On/off power switch (1) to turn on the unit.
u
Push the On/off power (1) switch to turn the unit off.
u
Cleaning the filters (Fig. F, G, H, I, J)
Press the dust chamber release button (2) as shown in
u
figure F.
Seperate the dust chamber (3) from the motor unit as
u
shown in figure F.
6
(Original instructions)
Lift the filter (8) out of the dust chamber (3) using the tab
u
provided as shown in figure G.
Empty the dust bowl (3) by lightly shaking over a suitable
u
container as shown in figure H.
The Filter and pre-filter can be separated to allow better
u
cleaning.
Twist the filter (8) in an anti-clockwise direction and lift
u
from the pre-filter (7) as shown in figure I.
Rinse out the dust-bowl with warm soapy water as shown
u
in figure J.
Wash the filters with warm soapy water as shown in figure
u
J.
Allow the filters to dry naturally, using heat may cause the
u
filters to distort.
Refit the filter (8) into the pre-filter (7) and then reinsert
u
into the dust chamber (3). Never place the filters into
the dust chamber backwards.
Replace the dust chamber onto the motor unit. Make sure
u
the release button (2) clicks into place.
Warning! Before performing any maintenance or cleaning on
the appliance, unplug the appliance.
From time to time wipe the appliance with a damp cloth.
Do not use any abrasive or solvent-based cleaner. Do not
immerse the appliance in water.
Maintenance
Your BLACK+DECKER cordless appliance has been designed
to operate over a long period of time with a minimum of main-
tenance. Continuous satisfactory operation depends upon
proper tool care and regular cleaning.
Warning! Before performing any maintenance on cordless
appliances:
Run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Replacing the filters
The filters should be replaced every 6 to 9 months and when-
ever worn or damaged. Replacement filters are available to
purchase form your local BLACK+DECKER service team.
Remove the old filters as described above.
u
Fit the new filters as described above.
u
Protecting the environment
Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.