Publicité
Antenna - Morsetti 4 e 5 di J2
Pulsante di start apre NO - Morsetti 1 e 3 di J2
Pulsante di start chiude NO - Morsetti 2 e 3 di J2
Importante: Prima di avviare la tapparella verificare che le con-
nessioni alla scheda elettronica siano corrette. A tal fine verificare
anche la commutazione dei contatti elettrici.
PROGRAMMAZIONE
Logica Passo-Passo
JP1
jumper non inserito
1
2
3
Modalità ciclico
JP1
jumper inserito tra 1 e 2
1
2
3
JP1
Logica Uomo Presente
jumper inserito tra 2 e 3
1
2
3
Apprendimento codici radiocomando
Premere il tasto P2 una volta per inserire un codice di apertura.
Premere il tasto P2 due volte per inserire un codice di chiusura.
Ogni pressione del tasto è seguita da un lampeggio di conferma
del led LD1. Distanziare di almeno 1 secondo una pressione del
tasto P2 dalla successiva. Quando il led si accende di luce fissa
trasmettere con il radiocomando il codice da apprendere.
Cancellazione memoria codici
Premere il tasto P2 fino allo spegnimento del led LD1 (circa 10
secondi).
Impostazione tempo di lavoro
Premere il pulsante Start chiude o il corrispondente tasto sul
radiocomando fino alla completa chiusura della tapparella.
Premere il tasto P1 per circa 3 secondi (accensione del led con
luce fissa) fino alla partenza della tapparella in apertura. A com-
pleta apertura premere nuovamente il tasto P1. La tapparella si
arresta ed il led si spegne.
TECHNICAL FEATURES
RADIORECEIVER The electronic unit contains a two-channel
radio receiver allowing remote control of the roller shutter by
means of the radio transmitter. The radio receiver channel 1 acts
as Opening start, whereas channel 2 acts as Closing start. The
radio receiver operates with a self-learning logic and can store up
to 120 different codes from the radio-commands. Each code may
be addressed on the desired channel (opening start or closing
start). The memory contents is preserved in absence of power
supply. The memory contents may be erased (total cancellation).
WORK TIME The motor's work time is controlled by one digital
timer. For the automation system to work properly the operating
time value to be set must be slightly (min. 2 sec.) above the roller
shutter's actual work time. If any command interrupts the roller
shutter's travel before its end, the Timer stops and the elapsed
time is stored in memory. Therefore the unit can determine, with
a fair approximation, the partial working time necessary to the rol-
ler shutter to end its travel. In case of limit switch lack, thanks to
this feature it is possible to avoid that the motor works for a long
time after the end of the roller shutter's travel, thus reducing
overheating to the minimum.
OPERATION MODES
INTRODUCTION The electronic unit contains a micro-processor
to control the roller shutter's operation modes. These are the
main operation modes:
"Step-by-step" mode (JP1 jumper=not inserted)
When the roller shutter is closed, the opening start command
determines an opening cycle. At the end of the work time, the rol-
ler shutter stops. The operating cycle is completed and the
system waits for a closing start command. If a opening start or
closing start command is supplied when the end of travel has not
been reached yet the roller shutter stops.
Manual (JP1 jumper=inserted between 3 and 2)
220
The roller shutter move until the (opening or closure) push-button
is pressed.
Note: The opening start and closing start commands can be sup-
plied by the two push-buttons of radio-command.
"Cyclical" mode (JP1 jumper=inserted between 1 and 2)
In cyclical mode the difference between the opening start and
closing start commands is cancelled and both commands have
the same function. The operation is controlled by a single start
command. In cyclical mode the "step-by-step" operation logic
remains unchanged.
Notice: The operation logic setting (jumper) and the work time
programming must be carried out only if the cycle is concluded or
before it starts (with closed roller shutter).
ELECTRICAL AND MECHANICAL
SPECIFICATIONS
Dimensions and weight:
Mains power supply:
Operating temperature range:
Single-phase motor power supply:
Motor's work time:
Operating frequency:
Radio receiver RF sensitivity:
Caution: The unit must be not switched on if the connected
loads or the power supply exceed the a.m. limits. Failure to
observe this precaution can result in damage to persons, animals
or objects for which the manufacturer cannot be held responsible.
ELECTRIC CONNECTIONS
2 electric connectors are fitted to the card:
1) J1 5-pole Terminal board for the connection of the devices
operating with 230Vac mains power supply (motor and mainsca-
ble)
1) J2 5-pole Terminal board for the connection of the devices
operating at low voltage (commands and aerial)
Terminal board J1
Terminal 1 - 230 Vac mains power supply phase
Terminal 2 - 230 Vac mains power supply neutral
Warning: The power supply voltage polarities must be carefully
observed.
Terminal 3 - 230 Vac motor M1 power supply common
Terminal 4 - 230 Vac motor M1 power supply phase (opening)
Terminal 5 - 230 Vac motor M1 power supply phase (closure)
Note: connect the capacitor of the motor M1 between terminals 4
and 5
Terminal board J2
Terminal 1 - Opening start push-button's normally open electric
contact
Terminal 2 - Closing start push-button's normally open electric
contact
Terminal 3 - Common terminal for all electric contacts of com-
mands
Terminal 4 - Aerial input (signal)
Terminal 5 - Aerial input (shield)
CONNECTION OF THE DEVICES
230 Vac mains power supply cable and ground - Terminals 1
and 2 on J1
Warning: The cable's ground pole must be connected to a good
ground reference in the roller shutter's nearby area.
Motor 1 - Terminals 3, 4 and 5 on J1
Aerial - Terminals 4 and 5 on J2
NO Opening start push-button - Terminals 1 and 3 on J2
NO Closing start push-button - Terminals 2 and 3 on J2
Important: Before starting the roller shutter check all connec-
tions to the electronic card. Check also the electriccontacts' swit-
ching.
88x127x58 mm - 0,3 kg
230 Vac +/- 10%
0 to + 60°C
230 Vac 1 HP max
programmable, 1 to 250 sec.
433.92 MHz
approx. -102 dBm
Publicité
