Matco Tools MT2612 Guide Rapide

WARNING
Study, understand and follow all instructions provided
with this product. Read these instructions carefully
before installing, operating, servicing or repairing this
tool. Keep these instructions in a safe, accessible place.
INTENDED USE OF THE TOOL
The MT2612 is designed to remove and install fasteners
with impact grade bits and sockets only. Do not run
excessive air pressures with this tool. Do not use this
tool outside of the designed intent. Never modify the
tool for any other purpose or use.
WARNING
Caution: To help prevent personal injury
• Use of this product can expose you to chemicals
including ethylene glycol, gasoline vapors and engine
exhaust, which are known to the State of California to
cause cancer, birth defects, or reproductive harm. For
more information, visit www.P65Warnings.ca.gov.
Always wear ANSI approved safety equipment, safety
glasses and clothing when using this product. Study,
understand, and follow all instructions provided with
this product. Failure to read and follow all warnings
and operating instructions may result in damages and
serious injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and bystanders).
• Never use this tool for any application other than for
which it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with
accessories not designed for it could result in serious
injury or death.
• Always select the correct accessories of the correct
size and design for the job that you are attempting to
perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is
in a secure position, and will not move during repair.
BEFORE USE
When unpacking, check the parts diagram and part
number listing on page 4 to make sure all parts are
included. If any parts are missing or damaged, please
call your distributor.
DO NOT DISCARD – GIVE TO USER
1/2" DUAL FLEX
ANGLE IMPACT WRENCH
The manufacturer warrants this product to the original user against
defective material or workmanship for a period of 1 year from the date
of purchase.
The manufacturer reserves the right to determine whether the part
or parts failed because of defective material, workmanship or other
causes. Failures caused by accident, alteration, or misuse are not
covered by this warranty.
The manufacturer, at its discretion, will repair or replace
product covered under this warranty, free of charge. Repairs or
replacements of products covered under this warranty are warranted
for the remainder of the original warranty period.
The manufacturer or its authorized service representatives must
perform all warranty repairs. Any repair to the product by
unauthorized service representatives voids this warranty. The rights
under this warranty are limited to the original user and may not be
transferred to subsequent owners.
The warranty is in lieu of all other warranties, expressed or implied,
including warranties of merchantability and fitness for a particular
purpose. Some states do not allow the exclusion or limitations of
incidental or consequential damages, so the above limitations may
not apply to you.
Authorized Matco Repair Centers:
United States
Matco Air Tool Repair SV
1330 Commerce Drive
Stow, OH 44224
(800) 433-7098
NMG Industrial WTRC
Attn: South Dock 2223 S.
Wilson Street Tempe, AZ 85282
PRODUCT INFORMATION:
Dual Flex. Adjustable in two new revolutionary ways,
up to 180° flex-head and 360° of handle rotation for
fitting both the impact head and your hand where
they need to.
Extreme low-profile. With an industry leading length of
around 3 ", fit your impact wrench where previously
only hand tools would.
Power where you need it. New patented air motor
design delivers the power despite its size for
400 ft. lbs. of breakaway torque.
SPECIFICATIONS
Square Drive: 1/2"
Working Torque: 280 ft. lbs.
Breakaway Torque: 400 ft. lbs.
Overall Length: 3.34"(85mm)
Air Inlet: 1/4"
Free Speed: 8000 RPM
Page 1
1 YEAR LIMITED WARRANTY
Canada
H. T. Pneumatic Rebuilders Inc.
22 Goodmark Place
Units 7 & 8
Toronto, Ontario M9W6R2
Air Pressure: 90psi
Clutch Type: Twin Hammer
Recommended Minimum
Hose Bore Diameter: 3/8"(10mm)
Recommended Maximum
Hose Length: 30'(10m)
Av. Air Consumption: 4 CFM
MT2612
Made in Taiwan
to Matco specifications
2012274-14