Publicité
Les langues disponibles
Les langues disponibles
10
Preparing to install
• Adjustable head rest
1a
• Shoulder pads (2x)
1b
• Side support
1c
• Shoulder straps (2x)
1d
• Harness buckle
1e
• Seat cushion
1f
• Central adjuster
1g
• Reclining handle
1h
• Release handle head rest
1i
• Front brace
1j
Installation of the seat on the i-Size base
1. Check if the ISOfix and floor support indicators on the base are
green. (2)
2. Make sure that the front brace is installed on the base. The
operation of the front brace is described in the user manual for the
base. (2)
3. Make sure that the seat is always in the release position when you
want to install the seat on the base or take the seat off the base. The
two yellow arrows on the seat and the base must be aligned. (3) Use
the reclining handle to adjust the recline position, see
4. Position the seat in the correct position on the base untill it clicks
with the base and the indicator at the front shows green. (3)
5. When the seat is positioned rearfacing on the back seat of the
vehicle, you should, if possible, push the front seat of the vehicle
backwards, so that it is in contact with the child seat (4). If it is not
possible to obtain contact with the child seat, push the back rest of
the front seat of the vehicle forward as far as possible.
6. The seat can be taken off and turned around by pulling the seat
release handle at the front of the base (5,6). Make sure that the
two yellow arrows on seat and seatbase are aligned; this is the only
position where you can take off the seat.
7. The seat should only be turned around to forward facing when the
child is minimum 88 cm and 15 months. BeSafe recommends to use
the seat rearfacing for as long as possible.
8. When the seat is positioned forward facing, the front brace has to be
in position 1. (7)
9. The seat cannot be turned around in the BeSafe iZi Modular RF. This
seat is only to be used rearfacing.
10. The seat can be reclined by pulling the reclining handle at the front
side of the seat. (8)
11. In a rearfacing position the seat should only be used in the 2 most
reclined positions. (9)
12. The leg room of the seat, in rearfacing position, can be made larger by
pulling the front brace box out from the base. The front brace box has
3 positions. To adjust the front brace position, the seat has to be taken
off and the base should be released from the ISOfix. (10)
13. The seat is delivered with removable SIP+ (side impact protection
+). This extra side impact protection should be used on the doorside
of the vehicle. To connect your SIP+ version, follow the instruction
drawings on the SIP+ included with your seat. The seat already offers
high level integrated side impact protection. This extra side impact
protection improves the protection in the side impact still further. (Not
on all models) (11)
14. Do not use the SIP+ on the seat when the space between seat and
door of the vehicle is too small, which might lead to a situation where
the seat is not positioned correctly on the vehicle seat.
Removal of the seat of the i-Size base
step 6.
1. The seat can be taken off by pulling the seat release handle at the
front of the base. Make sure that the two yellow arrows on seatbase
and seatbase are aligned; this is the only position where you can take
off the seat.
Positioning of the child
1. Check that the shoulder strap slots are level with your child's
shoulders. (12)
2. While pressing the button of the central adjuster, pull the shoulder
straps away from the seat with a flat hand. Make sure to pull the
straps evenly so that they stay at the same length. (13)
3. Open the harness buckle. (14)
4. The height of the shoulder straps and the head rest can be adjusted
by pulling the release handle upwards at the back of the head rest
and pulling the head rest up or down. (15)
5. Position the shoulder straps over the marking at the sides of the seat
to use the magnets to keep the harness open while you position the
child. (16)
11
Publicité
