Fein ASte649-1 Mode D'emploi page 15

OBJ_BUCH-0000000004-001.book Page 15 Tuesday, April 6, 2010 1:05 PM
Character Unit of measure,
internationall
P W
1
P W
2
n /min
0
n m/min
S
U
V
f
Hz
M... mm
L dB
wA
L dB
pA
L dB
pCpeak
K...
2
a
m/s
2
a
m/s
h,D
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
min, m/s
For your safety.
Read all safety warnings and all
WARNING
instructions. Failure to follow the
warnings and instructions may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
Do not use this power tool before you have thor-
oughly read and completely understood this
Instruction Manual and the enclosed "General
Safety Instructions" (document number
3 41 30 054 06 1). The documents mentioned should be
kept for later use and enclosed with the power tool,
should it be passed on or sold.
Please also observe the relevant national industrial safety
regulations.
Intended use of the power tool:
Hand-guided jigsaw for cutting metal, sandwich materials,
plastics and wood in weather-protected environments
using the application tools and accessories recommended
by FEIN.
Special safety instructions.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory
may contact hidden wiring or its own cord. Cutting acces-
sory contacting a "live" wire may make exposed metal
parts of the power tool "live" and could give the opera-
tor an electric shock.
Keep your hands well away from the saw blade. Do not
place your hands in front of or underneath the saw blade.
Any contact with the saw blade can cause personal inju-
ries. The saw blade can become very hot during the saw-
ing process.
Unit of measure,
national
W
W
rpm
m/min
V
Hz
mm
dB
dB
dB
2
m/s
2
m/s
m, s, kg, A, mm, V,
W, Hz, N, °C, dB,
2 2
rpm, m/s
Wear personal protective equipment. Depending on the
application, use a face shield, safety goggles or safety
glasses. Wear ear protection. The safety glasses must be
capable of protecting against flying particles generated by
the various different operations. Prolonged exposure to
high intensity noise may cause loss of hearing.
Secure the workpiece firmly. A work piece that is gripped
tightly in a clamping device or vice, is more secure than if
held by hand.
Do not rivet or screw any name-plates or signs onto the
power tool. If the insulation is damaged, protection
against an electric shock will be ineffective. Adhesive
labels are recommended.
Do not use accessories which are not specifically
designed and recommended by the power tool manufac-
turer. Safe operation is not ensured merely because an
accessory fits your power tool.
Clean the ventilation openings on the power tool at regu-
lar intervals using non-metal tools. The blower of the
motor draws dust into the housing. An excessive accu-
mulation of metallic dust can cause an electrical hazard.
Before putting into operation, check the mains connec-
tion and the mains plug for damage.
Hand/arm vibrations
The vibration emission level given in this information
sheet has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is used
for different applications, with different accessories or
poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over
the total working period.
Explanation
Power input
Output
Stroke rate at no-load
Cutting speed
Rated voltage
Frequency
Size of metric thread
Sound power level
Sound pressure level
Peak sound pressure level
Uncertainty
Vibrational emission value according to EN 60745
(vector sum of three directions)
Mean vibrational value for sawing
Basic and derived units of measure from the inter-
national system of units SI.
en
15