Publicité
Les langues disponibles
Les langues disponibles
974451
Notes:
• Ensure the inside of the Tank (4) and the Filter Frame (14) are clean and
free from dirt before operating
• Make sure the Drain Cap (3) is closed and hand tight
• When the Tank is full, the float valve within the Filter Frame will close.
There will be an increase in motor speed and loss of suction when this
happens.
• The Extending Tube (24) can be adjusted to suit the user. Release the
Tube Latch (25) to adjust the length
Draining the liquid
WARNING: ALWAYS disconnect from the power supply before carrying out
any inspection, maintenance or cleaning.
1. Disconnect any attachments from the end of the vacuum hose
2. Lift the end of the Flexible Hose (2) up above head height so that any
liquid runs down into the Tank (4)
3. Position your vacuum cleaner so the Drain Cap (3) is above the drainage
area
Note: Make sure that no perishable object or material is within 3 metres
of the Drain Cap.
4. Unscrew the Drain Cap and allow the liquid to drain. Undo the Lid Clamps
(8) and remove the Lid (9)
5. Tip the rest of the liquid out of the Tank into the drainage area
Blowing
1. Ensure the inside of the Tank (4) and the Filter Frame (14) are clean and
free from dirt before operating
2. Ensure the Foam Filter (23) is clean and dry, and fitted to the Filter Frame
3. Replace the Lid (9) on top of the Tank
4. Close both Lid Clamps (8)
5. Remove the plastic Air Outlet Cover (26) already fitted to the Air Outlet
(10). It has a small clip underneath so press at the underside of the cover
before pulling out
6. Attach the Flexible Hose (2) to the Air Outlet
WARNING: Point the small end of the Flexible Hose well away from any
object or person; debris may be ejected from the hose end
7. Switch on the vacuum cleaner by pressing the On/Off Switch (12) into
the 'I' position
8. Wait a few minutes for waste to be released from the end of the hose
before blowing
Using the Power Take Off (PTO) function
Note: This vacuum cleaner can be used to power another electrical device,
e.g. a power tool, up to 2000W.
1. Check that the On/Off Switch (12) is in the '0' (OFF) position
2. Connect the vacuum to the mains power supply
WARNING: If the device has a power switch, make sure it is switched OFF
before plugging into the Power Take Off Socket (13)
3. Plug the device into the Power Take Off Socket (power will be
automatically provided through the PTO Socket)
Note: If using the vacuum cleaner as a dust extraction device, connect the
Flexible Hose (2) to the tools dust extraction port, before powering on.
4. Press the On/Off Switch to 'II' (ON) to start the vacuum cleaner
Accessories
• A range of accessories and consumables, including filters and bags, is
available from your Silverline stockist. Spare parts can be obtained from
toolsparesonline.com
1250W Wet & Dry Vacuum Cleaner 30Ltr
Maintenance
WARNING: ALWAYS disconnect from the power supply before carrying out
any inspection, maintenance or cleaning.
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear.
Repairs should be carried out by an authorised Silverline service centre.
This advice also applies to extension cords used with this tool
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts
to wear quickly, and shorten the machine's service life. Clean the body of
your machine with a soft brush, or dry cloth. If available, use clean, dry,
compressed air to blow through the ventilation holes
• Clean the tool casing with a soft damp cloth using a mild detergent. Do
not use alcohol, petrol or strong cleaning agents
• Never use caustic agents to clean plastic parts
Filter cleaning
Note: A clogged filter will cause suction power and cleaning efficiency to
deteriorate. Check whether the filter is blocked if performance deteriorates.
• Detach the Lid (9), to gain access to the Foam Filter (23)
• Remove and clean the Filter using a brush and dry compressed air
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable
spray lubricant
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools that
are no longer functional and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic
equipment (WEEE), with household waste
• Contact your local waste disposal authority for information on the correct
way to dispose of power tools
www.silverlinetools.com
7
Publicité
