Publicité
Les langues disponibles
Les langues disponibles
OWNER'S MANUAL
SETUP INSTRUCTIONS
PLEASE REFER TO THE EXPLODED VIEW DRAWING IN THIS MANUAL IN ORDER TO IDENTIFY PARTS.
1.
Feed the black hose (#64) and orange hose (#63) coming out of the bottom of the handle assembly (#76) through the handle-1 (#52)
while at the same time lining up the hole in the handle-1 (#52) with the hole in the handle connector (#55). Secure them together with
the screw (#54).
2.
Thread two nuts (#53) all the way on the bottom of the tie rod (#50). Thread the bottom of the tie rod all the way inside the slotted pin
(#49). Now tighten one nut (#53) down on top of the slotted pin (#49) and tighten. Slip the spring (#51) down on the tie rod (#50). Insert
the tie rod (#50) through the bottom of the bracket that is welded to the handle-1 (#52) so that the spring is trapped between the
bracket and the nuts (#53) that are tightened against the slotted pin (#49). Compress the spring until the cross hole in the tie rod (#50)
is visible on the other side of the welded bracket and install the r-pin (#71) through the hole.
3.
Thread another nut (#53) all the way on the tie rod (#56). Hold the handle lock (#58) down and away from the t-handle-2 (#60) while
simultaneously threading the tie rod (#56) nut onto the tie rod (#50).
4.
Raise the handle lock (#89) up so the slotted pin (#49) does not come in contact with any of the three holes in the handle position
seat assembly (#7). Remove the screw (#79) from the handle socket (#11). Insert the handle-1 (#52) in the handle socket (#11) while
simultaneously inserting the slotted pin (#49) in the handle socket (#11) guide holes. Make sure the hole in the lower portion of the
handle-1 (#52) aligns with the threaded hole in the handle socket (#11) and secure them together with the screw (#79). Move the handle
up and down while simultaneously pulling the handle lock down so the slotted pin (#49) will engage with any of the three locking holes
in the handle position seat assembly (#7). Make sure the slotted pin will engage all three holes. It might be necessary to adjust the
threaded connection between tie rods (#50 and #56) in order to get proper engagement. After final adjustment, tighten the nut (#53)
to secure the connection.
5.
There are two air hoses that must be firmly inserted into the couplers (#48). The orange hose (#63) fits in the higher located coupler
while the black hose (#64) fits in the lower located coupler.
6.
Install the air quick disconnect of your choice in the cross valve (#65). Put at least two wraps of pipe dope tape around the disconnect
threads before installation to prevent air leaks.
7.
Install the bracket assembly (#72) on the handle-1 tube in the position as shown on the cover of the Owner's Manual and secure the
adapters in the bracket holes using the r-pins (#69).
8.
Due to the back pressure release system design of this jack, the jack's hydraulic system very rarely becomes air bound. Indication of
an air bound system is a ram that does not rise smoothly. In some extreme case of an air bound system, air can be purged by following
this procedure:
PURGING AIR FROM THE HYDRAULIC SYSTEM
a. Raise the ram (#32) to maximum height and then lower it all the way down following the activation directions on top of the handle.
b. Repeat step "a" several times until all air is purged from the system.
OPERATING INSTRUCTIONS
This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death.
IMPORTANT: Before attempting to raise any vehicle, check vehicle service manual for recommended lifting surfaces.
OPERATION:
1.
Become familiar with the identification and function of the operating jack components.
a. The ram (#32) is the shaft that comes out of the jack when you rotate the air lever to the right.
b. The ram (#32) is equipped with an extension screw which can be unscrewed to extend from the ram if there is not enough
hydraulic stroke to raise the load to the desired height. If additional height is required, extension adapters can be inserted
in the hole on top of the extension screw.
c. Larger diameter saddles can be inserted in the extension screw when requiring a larger diameter saddle surface.
2.
Chock the vehicle's tires that will not be lifted off the ground prior to lifting the vehicle and if available, apply the emergency brake
or any other method of braking.
3.
Position the jack at the designated lift point. Estimate the required ram travel to raise the vehicle to the desired height. If the desired
vehicle height exceeds the entire ram travel, unscrew the extension screw to make up the difference and add an extension adapter
if necessary.
4.
Lock the handle in a position that will not interfere with the vehicle when raised or lowered. Keep the handle in that locked position until
the work is completed and you are ready to remove the jack from use.
5.
With the jack in the lowered position, push the jack under the vehicle. IMPORTANT: Use the vehicle manufacturer's recommended lifting
procedures and lifting points before lifting loads.
6.
In most cases 100 psig input air pressure (do not exceed 200 psig) will lift the maximum capacity load not to exceed 22 tons. Rotate the
air lever to the right until the top of the ram comes close to the designated lift point. Make sure the designated lift point is flat, parallel
to the ground and free from grease, any kind of lubricant, and debris. Proceed with pumping the jack in order to lift the vehicle to the
desired height. During lifting, inspect the position of the jack in relation to the ground and the ram in relationship to the load to prevent
any unstable conditions from developing. If conditions look like they are becoming unstable, slowly lower the load and make appropriate
setup corrections after the load is fully lowered.
6722 Rev. A
TRUCK AXLE JACK WITH AIR RETURN
3
6722
CAPACITY: 22 TON
Rev. 3/13/17
Rev. A
Publicité
