Table des Matières
Publicité
2. Table Modbus
Project :
Subject:BMS integration points with Leak Detection system
PANEL TYPE : FG-NET
Location :
IP Address :
XXX.XXX.XXX.XXX
PROTOCOL : MODBUS TCP port 502
and/or, Serial MODBUS RTU, use ONE SERIAL INTERFACE ONLY, RS232 OR RS422 OR RS485
RS 232: Use 3 points terminal and crossover cable
RS 422: Use 4 points terminal and crossover cable
RS 485: Use 4 points terminal and loop Rx- with Tx- for DATA-, and Rx+ with Tx+ for DATA+
BAUDRATE : 9600 (can't be changed)
PARITY : NO (can't be changed)
STOP BIT: 1 BIT STOP, 8 DATA BITS (can't be changed)
SLAVE NUMBER can be set from 1 to 247
CABLE NAME
DEVICE ID
CABLE NUMBER
DESCRIPTION
SET ON PANEL
(SLAVE NO)
1_01
CABLE 1_01
1
1_02
CABLE 1_02
1
1_03
CABLE 1_03
1
1_04
CABLE 1_04
1
1_05
CABLE 1_05
1
1_06
CABLE 1_06
1
1_07
End Plug
1
2_01
CABLE 2_01
1
2_02
CABLE 2_02
1
2_03
CABLE 2_03
1
2_04
CABLE 2_04
1
2_05
CABLE 2_05
1
2_06
End Plug
1
3_01
CABLE 3_01
1
3_02
CABLE 3_02
1
3_03
End plug
1
CABLE INFORMATION
TYPE: Types can be Leaks, or Cable Break Bus (communication loss), or Cable Break Sensor (only the sensing part), or Cable Break End of Circuit (missing end plug), bit 7 is a common fault for these three Cable Breaks, show this register in Binary.
STATE: States can be New, or Seen, or Acknowledged, or Ejected, when a cable is ejected, the TYPE and LOCATION Registers won't code alarms anymore, show this register in Binary.
LOCATION: Locations are given in meters, the system will return a 0 value when there is no alarm, associations will affect this value and the location is always given as per the panel display (I.E. 587 meters), show this register in Decimal.
CHECK SECOND SHEET FOR BITS LAYOUT
ADDITIONAL REGISTERS
4096 FOR SYSTEM GLOBAL STATUS, this will show if there is any Leak or Cable Break anywhere on the Panel
4097 FOR CIRCUIT 1 GLOBAL STATUS, this will show if there is any Leak or Cable Break anywhere on Circuit 1
4098 FOR CIRCUIT 2 GLOBAL STATUS, this will show if there is any Leak or Cable Break anywhere on Circuit 2
4099 FOR CIRCUIT 3 GLOBAL STATUS, this will show if there is any Leak or Cable Break anywhere on Circuit 3
CHECK SECOND SHEET FOR BITS LAYOUT
TYPE INFORMATION
TYPE
BIT POSITION
TYPE
REGISTER ADDRESS
CABLE BREAK
CABLE BREAK
LEAK
BUS
SENSOR
CIRCUIT 1 (up to 40 cables from 1_01 to 1_40)
7101
bit 4
bits 0+7
bits 1+7
7102
bit 4
bits 0+7
bits 1+7
7103
bit 4
bits 0+7
bits 1+7
7104
bit 4
bits 0+7
bits 1+7
7105
bit 4
bits 0+7
bits 1+7
7106
bit 4
bits 0+7
bits 1+7
7107
N/A
N/A
N/A
CIRCUIT 2 (up to 40 cables from 2_01 to 2_40)
7201
bit 4
bits 0+7
bits 1+7
7202
bit 4
bits 0+7
bits 1+7
7203
bit 4
bits 0+7
bits 1+7
7204
bit 4
bits 0+7
bits 1+7
7205
bit 4
bits 0+7
bits 1+7
7206
N/A
N/A
N/A
CIRCUIT 3 (up to 40 cables from 3_01 to 3_40)
7301
bit 4
bits 0+7
bits 1+7
7302
bit 4
bits 0+7
bits 1+7
7303
N/A
N/A
N/A
STATE INFORMATION
STATE
BIT POSITION
STATE
REGISTER ADDRESS
CABLE BREAK
NEW
SEEN
END PLUG
N/A
8101
bit 0
bit 1
N/A
8102
bit 0
bit 1
N/A
8103
bit 0
bit 1
N/A
8104
bit 0
bit 1
N/A
8105
bit 0
bit 1
N/A
8106
bit 0
bit 1
bits 2+7
8107
bit 0
bit 1
N/A
8201
bit 0
bit 1
N/A
8202
bit 0
bit 1
N/A
8203
bit 0
bit 1
N/A
8204
bit 0
bit 1
N/A
8205
bit 0
bit 1
bits 2+7
8206
bit 0
bit 1
N/A
8301
bit 0
bit 1
N/A
8302
bit 0
bit 1
bits 2+7
8303
bit 0
bit 1
95
FG-NET_Operation & Installation Manual_FR_v3.1.6_202009.docx
LOCATION (m)
LOCATION
BIT POSITION
LOCATION
REGISTER ADDRESS
ACKED
EJECTED
LOCATION (m)
bit 2
bit 3
9101
bits 0 to 15
bit 2
bit 3
9102
bits 0 to 15
bit 2
bit 3
9103
bits 0 to 15
bit 2
bit 3
9104
bits 0 to 15
bit 2
bit 3
9105
bits 0 to 15
bit 2
bit 3
9106
bits 0 to 15
bit 2
bit 3
9107
N/A
Will code Break End of Circuit fault only
bit 2
bit 3
9201
bits 0 to 15
bit 2
bit 3
9202
bits 0 to 15
bit 2
bit 3
9203
bits 0 to 15
bit 2
bit 3
9204
bits 0 to 15
bit 2
bit 3
9205
bits 0 to 15
bit 2
bit 3
9206
N/A
Will code Break End of Circuit fault only
bit 2
bit 3
9301
bits 0 to 15
bit 2
bit 3
9302
bits 0 to 15
bit 2
bit 3
9303
N/A
Will code Break End of Circuit fault only
Sep 2020 – Version 3.1.6
REMARKS
Publicité
Table des Matières
