Publicité
Les langues disponibles
Les langues disponibles
faIlure tO OBSerVe theSe WarnIngS cOuld reSult In InJury
thIS
InStructIOn
ImPOrtant Safety InfOrmatIOn.
read thIS InStructIOn manual carefully
and underStand all InfOrmatIOn BefOre
OPeratIng thIS tOOl.
It is the responsibility of the owner to make sure all
personnel read this manual prior to using the tool. It is also
the responsibility of the device owner to keep this manual
intact and in a convenient location for all to see and read.
If the manual or product labels are lost or not legible,
contact Matco Tools for replacements. If the operator is
not fluent in English, the product and safety instructions
shall be read and discussed with the operator in the
operator's native language by the purchaser/owner or his
designee, making sure that the operator comprehends its
contents.
• Always operate, inspect and maintain this tool in
accordance with American National Standards Institute
Safety Code of Portable Air Tools (ANSI B186.1) and any
other applicable safety codes and regulations.
• For safety, top performance and maximum durability of
parts, operate this tool at 90 psig; 6.2 bar max air
pressure with 3/8" diameter air supply hose.
• Always wear impact-resistant eye and face protection
when operating or performing maintenance on this tool,
users and bystanders.
• Always wear hearing protection when using this tool.
High sound levels can cause permanent hearing loss.
Use hearing protection as recommended by your
employer or OSHA regulation, users and bystanders.
• Always wear breathing apparatus (users and
bystanders).
• To reduce exposure to polishing debris, work in a well
ventilated area with proper personal protection
equipment.
• Keep the tool in efficient operating condition.
• Operators and maintenance personnel must be
physically able to handle the bulk, weight and power of
this tool.
• Air powered tools can vibrate in use. Vibration, repetitive
motions or uncomfortable positions over extended
periods of time may be harmful to your hands and arms.
Discontinue use of tool if discomfort, tingling feeling or
pain occurs. Seek medical advice before resuming use.
• Air under pressure can cause severe injury. Never direct
air at yourself or others. Always turn off the air supply,
drain hose of air pressure and detach tool from air supply
before installing, removing or adjusting any accessory
on this tool, or before performing any maintenance on
this tool. Failure to do so could result in injury. Whip
hoses can cause serious injury. Always check for
damaged, frayed or loose hoses and fittings, and replace
immediately. Do not use quick detach couplings at tool.
See instructions for correct set-up.
• Slipping, tripping and/or falling while operating air
tools can be a major cause of serious injury or
death. Be aware of excess hose left on the walking
or work surface.
• Keep body working stance balanced and firm. Do
not overreach when operating the tool.
MT2466A
MT2466A METAL BLASTER
WARNING
manual
cOntaInS
2
• Anticipate and be alert for sudden changes in motion
during start up and operation of any power tool.
• Do not carry tool by the hose. Protect the hose from
sharp objects and heat.
• Tool shaft may continue to rotate briefly after throttle is
released. Avoid direct contact with accessories
during and after use. Gloves will reduce the risk of cuts
or burns.
• Keep away from rotating end of tool. Do not wear
jewelry or loose clothing. Secure long hair. Scalping
can occur if hair is not kept away from tool and
accessories. Choking can occur if neckwear is not
kept away from tool and accessories.
• Do not use accessories which are not specifically
designed and recommended by the tool manufacturer.
• Never use standard grinding wheels, wire brushes or
cutoff wheels with this tool.
• Correct wire belt and eraser mounting is necessary to
prevent injury. Do not use wire belts or eraser wheels
that have been broken or damaged in any way.
• Wheel hubs should be a free fit on the spindle to prevent
stress at the mounting location. Use only hubs that
come with the metal blaster for mounting wire belts and
eraser wheels.
• Flat washers or other adapters may over stress the
wheel hub. Always use factory recommended mounting
hardware.
• Tighten the wheel hub on the spindle to prevent spin off
when the tool is turned off and air supply disconnected.
• Use accessories recommended by Matco Tools.
• RPM OF THE ACCESSORY MUST EXCEED TOOL RPM.
RPM
RPM
RPM
Use accessories rated at 4,000 RPM or higher.
• Do not lock, tape or wire the "on/off" safety lever in the
"on" position, as the lever must be free to return to the
"off" position when released.
• Do not lubricate tools with flammable or volatile liquids
such as kerosene, diesel or jet fuel.
• Do not force tool beyond its rated capacity.
• Do not remove any labels. Replace damaged labels.
• This tool is not insulated against electric shock.
• Keep tool out of reach of children.
• Do not point or indulge in any horseplay with this tool.
• Note direction of rotation BEFORE operating this tool.
• This tool must not be used in explosive atmospheres.
• Do not use (or modify) the tool for any other purpose
than that for which it was designed without consulting
the manufacturer's authorized representative.
• Servicing and repairs should only be made by an
authorized service center.
• Failure to heed these warnings may result in serious
or fatal personal injury, property damage or both.
• This product may contain one or more chemicals known
to the State of California to cause cancer and birth
defects or other reproductive harm. Wash hands
thoroughly after handling.
Rev. 1/7/16
Publicité
