DWT KGS16-210 P Notice Originale page 25

• Loosen lock-nut 39�
• Adjust the cutting depth by turning bolt 38 in or out�
• Tighten lock-nut 39�
Vertical alignment of the body and adjustment of
the 45° tilt (see fig. 12-15)
• Position the body for carriage�
• Loosen lock lever 1 and set the body tilt
angle (90° or 45°)� Tighten lock lever 1�
• Place the sides of an alignment setsquare 90° or 45°
(depending on the angle to align) to the surface of saw
blade 5 and turntable 14� If the setsquare sides join
the surfaces of saw blade 5 and table 14 tightly, then
alignment is not needed, otherwise you have to do it�
Use bolt 40 and lock-nut 41 for vertical align-
ment of the body (see fig. 12, 14).
[KGS16-210 P]
Bolt 44 is used for adjusting the casing
slope 45° angle (see pic� 13)� Please note:
bolt 44 is spring-mounted and has no lock
nut, therefore it should be rotated in the
corresponding direction while adjusting the cas-
ing slope angle - its position will be fixed automati-
cally.
[KGS18-255 P]
Use bolt 44 and lock-nut 45 for adjustment
of the body tilt angle 45° (see fig. 15).
• Loosen lock lever 1�
• Loosen the lock-nut�
• Turning the adjustment bolt in or out, makethe sides
of the 90° or 45° setsquare (depending on the angle
to adjust) join the surfacesof saw blade 5 and table 14
tightly�
• Tighten the lock-nut�
• Loosen screw 43 and place indicator 42 to the 0°
(on scale 2) or 45° position (depending on the angle to
adjust), then tighten screw 43�
Retaining bar alignment (see fig. 16)
• Set the 0° horizontal cutting angle (the procedure is
described below)�
• Position the body for carriage�
• Place the sides of an alignment setsquare 90° to
the surface of saw blade 5 and retaining bar 11� If the
setsquare sides join the surfaces of saw blade 5 and
retaining bar 11 tightly, then alignment is not needed,
otherwise you have to do it�
• Loosen retainer bolt 26 with Allen key 32 and make
the side square elbow 90° bear against saw blade sur-
face 5 and retaining bar 11 surface by moving retaining
bar 11�
• Tighten retainer bolts 26�
Kerf indicating laser alignment (see fig. 17-18)
Before starting any work, ensure that the kerf indicat-
ing laser is properly aligned�
• Make a kerf in the blank, but do not cut it (the proce-
dure is described below)�
• Turn on the kerf indicating laser (using on / off
switch 33) - the laser beam should accurately point at
the kerf, otherwise - align the laser�
• Loosen screws 46�
• Move the body of kerf indicating laser 36 to theright
and left until the laser beam points accu-rately at the
kerf�
• Tighten screws 46�
Always use the correct supply voltage: the power sup-
ply voltage must match the information quoted on the
power tool identification plate.
Switching the power
Switching on:
Press blocking lever 23 to the left with your right hand
(see fig.19) - this will enable you to press on / off
switch 22 easily and pull the power tool body down�
Press on / off switch 22�
Switching off:
Release on / off switch 22�
the power tool operation
Dust suction allows reducing dust concen-
tration in the air and prevents its accumula-
tion at the workplace�
While operating the power tool, always
use dust bag 30 or a vacuum cleaner suitable for col-
lecting process-generated dust� A special adapter is
used to join the vacuum cleaner to coupler 3�
on the power tool operation
Alignment of the horizontal cutting angle (see
fig. 20)
• Loosen lock 17 and press fixing lever 16 (see fig. 20).
• While pressing lever 16, set the cutting angle by
turning table 14 by lock 17� Indicator 18 shows the set
cutting angle on scale 19�
• Release fixing lever 16 and tighten lock 17�
You can preset the most frequent angles (45°, 22�5°, 0°,
etc�)�
• Loosen lock 17 and press fixing lever 16�
• While pressing lever 16, set the cutting angle by
turning table 14 by lock 17� As soon as Indicator 18
shows one of the frequent angles (45°, 22�5°, 0°, etc�)
on scale 19 - release fixing lever 16, and the chosen
angle will be properly fixed, you do not have to tighten
lock 17 in this case�
Alignment of the vertical cutting angle (see fig. 21)
• Loosen lock lever 1�
• Set the cutting angle by tilting the power tool
body� Indicator 42 shows the set cutting angle on
scale 2�
• Tighten lock lever 1�
English
25
Initial operating
of the power tool
tool on / off
Dust suction during
Recommendations