Matco Tools MCL2012BIW Instructions De Fonctionnement page 5

FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.
SAVE THESE INSTRUCTIONS!
SAFETY INSTRUCTIONS FOR BATTERY
CHARGER AND BATTERY PACK
DANGER! READ CAREFULLY
120 Volts present at charging terminal. Absolutely DO NOT
probe with conductive objects.
1. CAREFULLY READ AND UNDERSTAND THESE
INSTRUCTIONS
This manual contains critical safety and operating instructions
for the tool, battery charger, and battery .
2 . Before using battery charger, read all instructions and
cautionary markings on (1) battery charger, (2) battery, and (3)
product using battery .
3 . CAUTION - To reduce risk of injury, charge only MATCO
rechargeable batteries marked on the charger label . Other
types of batteries may burst causing personal injury and
damage .
4 . Do not expose charger to rain or snow .
5 . Use of an attachment not recommended or sold by Matco
or the battery charger manufacturer may result in a risk of fire,
electric shock, or injury to persons .
6 . To reduce risk of damage to electric plug and cord, pull by
plug rather than cord when disconnecting charger .
7 . Make sure cord is located so that it will not be stepped on,
tripped over, or otherwise subjected to damage or stress .
8 . An extension cord should not be used unless absolutely
necessary . Use of improper extension cord could result in a
risk of fire and electric shock . If extension cord must be used,
make sure:
a . That pins on plug of extension cord are the same
number size, and shape as those of plug on charger;
b . That extension cord is properly wired and in good
electrical condition;
c . That wire size is at least as large as the one specified
in the table below .
Table 1: RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR BATTERY CHARGERS
Length of Cord (Feet)
AWG Size of Cord
9 . Do not operate charger with damaged cord or plug -
replace them immediately.
10 . Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way; take it to a
MATCO AUTHORIZED service facility .
11 . Do not disassemble charger or battery cartridge; take it to
your MATCO AUTHORIZED distributor service facility . Incorrect
reassembly may result in a risk of electric shock or fire .
MCL2012BIW, - G, - O
MCL2012BIW 20V
25 50 75 100 150
18 18 16 14 12
+ 1/2" Brushless Impact Wrench
WARNING
12 . To reduce risk of electric shock, unplug charger from
outlet before attempting any maintenance or cleaning . Turning
off controls will not reduce this risk .
13 . The battery charger is not intended for use by young
children or infirm persons without supervision .
14 . Young children should be supervised to ensure that they
do not play with the battery charger .
OPERATIONAL GUIDELINES FOR BATTERY
CHARGER AND BATTERY PACK
1 . Do not attempt to use a step-up transformer, an engine
generator or DC power receptacle .
2 . Do not allow anything to cover or clog the charger vents .
3 . Always cover the battery terminals with the box or cover
when the battery cartridge is not used .
4 . Do not short the battery cartridge:
5 . Do not store the tool and Battery Cartridge in locations
where the temperature may reach or exceed 50°C (122°F) .
6 . Do not incinerate the Battery Pack even if it is severely
damaged or is completely worn out . The battery cartridge can
explode in a fire .
7 . Be careful not to drop, shake or strike battery as it will
affect the capacity and may void warranty .
8 . Do not charge inside a box or container of any kind . The
charger and battery are ventilated devices and must NOT be
placed next to a heat source or in exposure to radiating heat .
9 . Place charger on a solid and sturdy surface as there are
vents on the bottom side of the charger .
10 . Always unplug the charger from the power supply when a
charging sequence is not taking place .
5
(1) Do not touch the terminals with any conductive
material .
(2) Avoid storing battery cartridge in a container with
other metal objects such as nails, screws, coins, etc .
(3) Do not expose battery cartridge to water or rain . A
battery short can cause a large current flow, overheating,
possible burns and even a breakdown .
rev 10/10/19