Publicité
Les langues disponibles
Les langues disponibles
OPERATION
Always turn off the air supply, drain hose of air pressure and detach
tool from air supply before installing, removing or adjusting any part or
accessory on this tool, or before performing any maintenance on this
tool.
After mounting sandpaper, start this sander under a bench in order to
make sure sandpaper is firmly attached. Set the sander down on the
work evenly and move it slowly back and forth in wide, overlapping
areas. Additional pressure may be used to make more efficient use of the
tool when material to be sanded is thick. Lighter pressure may be used
in delicate sanding or when using edges of sanding pad. When finished
sanding, lift it off the work before stopping the motor.
NOTE: During operation, safety goggles should always be worn to
guard against flying rust and chips (users and bystanders).
AIR SUPPLY
Tools operate on a wide range of air pressures. It is recommended that
air pressure measures 90 psig at the tool with the trigger fully depressed
and no load applied to the tool. Higher pressure (over 90 psig; 6.2 bar)
raises performance beyond the rated capacity of the tool, which will
shorten tool life and could cause injury.
Always use clean, dry air. Dust, corrosive fumes and/or water in the air
line will cause damage to the tool. Drain the water from air lines and
compressor prior to running tool. Clean the air inlet filter screen weekly.
The recommended hookup procedure can be viewed in FIG. 1.
The air inlet used for connecting air supply has standard 1/4" NPT. Line
pressure should be increased to compensate for unusually long air
hoses (over 25 feet). Minimum hose diameter should be 3/8" I.D. and
fittings should have the same inside dimensions and be tightly secured.
Ensure an accessible emergency shut off valve has been installed in the
air supply line and make others aware of its location.
WARRANTY
Matco warrants this air tool for a period of 1 year to the consumer . We
will repair any MT Series air tool covered under this warranty which
proves to be defective in material or workmanship during the warranty
period . In order to have your tool repaired, return the tool to one of
the Matco Authorized Warranty Centers listed, freight prepaid . Please
include a copy of your proof of purchase and a brief description of the
problem . The tool will be inspected and if any part or parts are found to
be defective in material or workmanship, the tool will be repaired free of
charge and returned to you freight prepaid .
This warranty gives you specific rights . You may also have other rights
which vary from state to state .
The foregoing obligation is Matco's sole liability under this or any implied
warranty and under no circumstances shall Matco be liable for any
incidental or consequential damages .
MT2332, MT2416, MT2432
MT2332, MT2416, & MT2432 Orbital Palm Sanders
FEATURES
• Low profile, low vibration 12,000 RPM variable speed palm sander
• Anti-dust shield system protects tool for longer life
• Anti-vibration system makes these tools easier to work with for extended periods
• Tip valve variable speed design for full throttle control
• Composite throttle lever is recessed for greater comfort
• Inner locking cylinder and motor design for super high performance
• Ergonomic cushion grip for comfort and stability
• Super quiet--only 80 dBA noise level-light, strong, comfortable and quiet!
LUBRICATION AND MAINTENANCE
Lubricate the air motor daily with high quality air tool oil. If no air line oiler
is used, run 1/2 oz. of oil through the tool. The oil can be squirted into the
tool air inlet or into the hose at the nearest connection to the air supply,
then run the tool. A rust inhibitive oil is acceptable for air tools.
WARNING: After an air tool has been lubricated, oil will discharge through
the exhaust port during the first few seconds of operation. The exhaust
port must be covered with a towel before applying air pressure to prevent
serious injury.
TROUBLESHOOTING
Other factors outside the tool may cause loss of power or erratic action.
Reduced compressor output, excessive drain on the air line, moisture
or restrictions in air pipes or the use of hose connections of improper
size or poor condition may reduce air supply. Grit or gum deposits in the
tool may cut power and may be corrected by cleaning the air strainer
and flushing out the tool with gum solvent oil or an equal mixture of
SAE #10 oil and kerosene. If outside conditions are in order, and the tool
continues erratic action or low power, disconnect tool from hose and
contact your nearest authorized service center.
Nipple
Air
inlet
Note: Some states do not allow the exclusion or limitation of incidental
or consequential damages so the above limitation or exclusion may not
apply to you .
NATIONAL MACHINE GROUP EAST
AIR TOOL REPAIR CENTER
1330 Commerce Dr.
Stow, OH 44224
(330) 688-6494
NATIONAL MACHINE GROUP WEST
AIR TOOL REPAIR CENTER
2223 S. Wilson Street
Tempe, AZ 85282
(480) 966-1097
HT PNEUMATIC REBUILDERS
22 Goodmark Place Unit #8
Toronto, ON M9w 6R2
(416) 213-0172
3
Fig. 1
Fig. 2
Rev. 11/20/15
Publicité
