Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
TELEPHONES PROGRAMMING
P
rogramación de los teléfonos T-740 Plus.
Set to ON the switch number 2 of the SW2 configuration dip switch, that's
accessible in the EL500SE module by opening the terminal connector protection
cover. The door panel will reproduce a sound to advise that the system has
entered into programming mode. In systems with more than one door panel,
the programming process shall be done on the master door panel only.
To program the telephone from a general door panel (if it exists), see page 116.
SW1
SW1
P3
SW1
ON
P3
SW1
ON
P3
SW1
P
ON
SW1
CN1
P1
P3
ON
P3
P2
SW1
S
ON
CN1
P1
SW1
CN2
P3
SW1
ON
ON
P3
P3
P2
SW1
SI
ON
CN1
P1
SW1
P3
SW1
CN2
ON
ON
P3
P3
P2
Each apartment must have one master unit only; in case of parallel units configure them as slaves,
both monitors or telephones.
CN2
Make a call to check that the telephone has been succesfully programmed. Repeat
these steps to program the rest of telephones.
Once the programming has been finished, set to OFF the programming switch. If
you don't, the door panel will reproduce a tone to advise that the system is still
into programming mode.
Open the telephone to programming (see page
P3
130). Select in the SW1 dip switch the fuction
mode for the auxiliary
function push button
(see page 129) and later press the P3
programming push-button.
CN1
P1
To show that the system is ready for programming,
the door panel and the telephone's handset will
reproduce a tone (the telephone led will light).
Audio communication can be established.
P2
CN1
P1
Press the door panel push button that will call to
this telephone. At this moment both door
panel and handset will reproduce tones (the
telephone led will slow blink).
P2
CN1
P1
To programm the telephone as Master, press the
h
ook switch
(the telephone led will off).
Close the telephone.
P2
CN2
CN1
P1
To programm the telephone as Slave, press the
CN1
P1
P1 door release push button (the telephone
led will quick blink) and later press the hook
P2
switch (the led will off).
Close the telephone.
P2
CN2
CN1
P1
To programm the telephone as Slave +
Intercom., press the P2 auxiliary function
CN1
P1
CN2
push button (the led will quick blink) and later
P2
press the hook switch (the led will off).
Close the telephone.
P2
CN2
CN2
CN2
131
132
C
onnexion of an a.c. lock release.
If an alternating current lock release has been installed, use a TF-104 transformer or an EL 502
dc/ac converter and connect it to the lock release as it is shown on the respective diagram.
FA-PLUS/C
rev.938072
PRI
230110 0
-
Main
IMPORTANT: If the TF-104 transformer is used
*
to supply the a.c lock release and the door
panel lamps, wire ~1/~2 terminals of the
sound module with CV1/CV2 terminals
respectively of the EL-500SE module.
L
ink of several power supplies units.
If the quantity of monitors or telephones to be connected is bigger than the supported from one
power supply (see page 118), use additional power supplies to match the required quantity. The
first power supply should be connected to the door panel and to the first group of monitors or
telephones; connect the next groups to the positive terminal of its corresponding power supply.
To wire several power supplies link their ground terminals.
NEVER link positive terminals of different power supplies.
1st FA-Plus
PRI
SEC
~
~
+ +
-
Main
INSTALLATION DIAGRAMS
EL502 dc/ac converter and a.c Lock release
EL502
SEC
CN1
CN2 CN3
-
CV-
CV+
-
+ +
+
-
CV2
Va.c
Lock release
TF-104 and a.c Lock release
TF-104
PRI
SEC
~ ~ ~ ~
Main
2nd FA-Plus/C or FA-Plus
PRI
SEC
~
~
-
+ +
-
-
To the second group of
Main
To the door panel & to the first
EL500SE
CN2
CV1
+12
AP - - +
+
EL500SE
CN2
-
CV2
CV1
+12
*
Va.c
Lock release
monitors/telephones.
group of monitors/telephones.
Publicité
Chapitres
Table des Matières
