F.F. Group PE 180/1400 E PLUS Notice Originale page 8

8 | English
Use special care when working corners, sharp
f
edges, etc. Avoid bouncing and snagging the ac-
cessory. Corners, sharp edges or bouncing have a
tendency to snag the rotating accessory and cause
loss of control or kickback.
Do not attach a saw chain woodcarving blade or
f
toothed saw blade. Such blades create frequent
kickback and loss of control.
SAFETY wARNINGS SpECIFIC FOR SANDING
OpERATIONS
Do not use excessively oversized sanding disc
f
paper. Follow manufacturers recommendations,
when selecting sanding paper. Larger sanding
paper extending beyond the sanding pad presents
a laceration hazard and may cause snagging, tearing
of the disc, or kickback
SAFETY wARNINGS SpECIFIC FOR pOLISHING
OpERATIONS
Do not allow any loose portion of the polishing
f
bonnet or its attachment strings to spin freely.
Tuck away or trim any loose attachment strings.
Loose and spinning attachment strings can entangle
your fingers or snag on the workpiece.
SAFETY wARNINGS SpECIFIC FOR wIRE BRUSH-
ING OpERATIONS
Be aware that wire bristles are thrown by the
f
brush even during ordinary operation. Do not
overstress the wires by applying excessive load
to the brush. The wire bristles can easily penetrate
light clothing and/or skin.
If the use of a guard is recommended for wire
f
brushing, do not allow any interference of the
wire wheel or brush with the guard. Wire wheel or
brush may expand in diameter due to work load and
centrifugal forces.
CONNECTION TO THE pOwER SUppLY
Make sure the power supply information on the
machine's rating plate are compatible with the
power supply you intend to connect it to.
This appliance is Class II* and is designed for con-
nection to a power supply matching that detailed
on the rating label and compatible with the plug
fitted. If an extension lead is required, use an ap-
proved and compatible lead rated for this appli-
ance. Follow all the instruction supplied with the
extension lead.
*Double insulated: This product requires
no earth connection as supplementary in-
sulation is applied to the basic insulation to
protect against electric shock in the event
of failure of the basic insulation.
GUIDELINES FOR USING EXTENSION CORDS
Make sure your extension cord is in good condi-
f
tion. When using an extension cord, be sure to
use one heavy enough to carry the current your
product will draw. An undersized cord will cause a
drop in line voltage resulting in loss of power and
overheating.
Always replace a damaged extension cord or have
f
it repaired by a qualified person before using it.
Protect your extension cords from sharp objects,
f
excessive heat and damp/wet areas.
Use a separate electrical circuit for your tools. This
f
circuit should be protected with the appropriate
time-delayed fuse. Before connecting the motor
to the power line, make sure the switch is in the
OFF position and the electric voltage is rated the
same as the voltage stamped on the motor name-
plate. Running at a lower voltage will damage the
motor.
PRODUCT SpECIFICATIONS
INTENDED USE
The machine is intended for polishing and brushing
metal and coated surfaces as well as for polishing
stone without the use of water.
TECHNICAL DATA
Article number
Model
Rated voltage
Rated power input
Rated speed
Sanding pad diam-
eter, max.
Thread of grinder
spindle
Max. spindle length
Weight
Sound emission values determined according
to EN 60745-1, ΕΝ 60745-2-3
Typically the A-weighted noise levels of the
product are:
Sound pressure
level
Sound power level
Uncertainty k
vibration total values a
and uncertainty k determined according to EN
60745-1, ΕΝ 60745-2-3
vibration level max:
a
h
k
IDENTIFICATION
1. Handle screw
2. D-shape handle
3. Spindle lock
4. Speed adjuster
5. On/Off switch
6. Bonnet
7. Polishing plate
8. Handle
9. Lock-on button
PE 180/1400 E PLUS
45 917
pE 180/1400 E pLUS
V 220-240
Hz 50
W 1400
min 600-3500
-1
mm 180
M14
mm 21
kg 3,3
dB(A) 89,5
dB(A) 100,5
dB 3
(triax vector sum)
h
m/s 1,785
2
m/s 1,5
2