F.F. Group RH 24/720 PRO Notice Originale page 5

Before using for the first time, ask for a
practical demonstration. If the cable is
damaged or cut through while working,
do not touch the cable but immediately
pull the mains plug. Never use the
machine with a damaged cable.
Wear safety glasses, protective gloves
and sturdy shoes. Wear ear protection
to prevent damage to your hearing.
The machine must not be damp and
must not be operated in a wet environ-
ment.
Keep long hair away from the machine.
Do not operate while wearing loose
clothing.
Connect the mains plug only when the tool is
f f
switched off. After using, pull the mains plug.
Always direct the cable to the rear away from the
f f
machine.
Do not carry the machine by the cable.
f f
When working with the machine, always hold it firm-
f f
ly with both hands and provide for a secure stance.
During pauses in the work, when not in use or during
f f
work on the machine itself (e.g., changing of the
working tools, repairs, cleaning, adjustment), pull the
mains plug.
Persons under 16 year of age are not permitted to
f f
operate this machine.
Keep the tool accessories out of the reach of children.
f f
Only use original accessories
f f
PRODUCT SPECIFICATIONS
Article number
Chuck type
Rated power input
Voltage
No load speed
Impact rate
Impact energy
Max. drilling diameter:
Concrete
Steel
Wood
Weight (without
accessories) approx.
Protection class
41 379
SDS Plus
W 720
V/Hz 230-240/50
min 0-1300
-1
min 0-4500
-1
J 2.6
mm 24
mm 13
mm 30
kg 2.7
/ II
Intended Use
The machine is intended for hammer drilling in con-
crete, brick and stone. It is likewise suitable for drilling
without impact in wood, metal, ceramic and plastic.
Product Elements
1. SDS - plus chuck
2. Tool holder (SDS - plus)
3. Dust protection cap
4. Locking sleeve
5. Depth stop
6. Auxiliary handle
7. Operational mode selection switch
8. Forward/reverse function lever
9. Lock-on button
10. On/Off switch
Not all the accessories illustrated or described in-
cluded in standard delivery.
BEFORE USE
Be careful of hidden electrical lines or gas
and water pipes. Check the working area, e.g.
with a metal detector. Always use the correct
supply voltage! The voltage of the power
source must agree with the value given on
the nameplate of the machine.
Tool Changing
Take care that the dust protection cap 3 is not dam-
aged when changing tools.
SDS - Plus Tools
The SDS - plus tool is designed to be freely
movable. This causes eccentricity when the
machine is offload. How ever, the drill au-
tomatically centers itself during operation.
This does not affect drilling precision.
Inserting
Clean and lightly grease the tool before inserting.
Insert the dust-free tool into the tool holder 2 with
twisting manner until it latches. The tool locks it-
self. Check the locking by pulling on the tool.
Removing
Pull the locking sleeve 4 to the rear and hold while
removing the tool.
Putting into Operation
Switching on: Press the on- off switch 10
Switching off: Release the on- off switch 10
Switching on/off in chiseling mode.
To lock the pressed on/off switch 10, push the
lock-on button 9 upward. To switch off the pow-
er tool. Release the on/off switch 10 or when it is
locked with the lock-on button 9, briefly press the
on/off switch 10 and then release it.
WORKING INSTRUCTIONS
Overload Clutch
If the drill bit becomes jammed or caught, the drive
to the drill spindle is interrupted.
•
Because of the forces that occur as a result,
always hold the machine with both hands and
take a secure stance. The machine should be
used only with an auxiliary handle.
Auxiliary Handle 6. You will be able to obtain a
English | 5
www.ffgroup-tools.com