Publicité
Les langues disponibles
Les langues disponibles
6
| English
Vibration total values a
and uncertainty K determined according to EN
60745-1
Vibration Level
a
h
K
Battery:
Type
Voltage
Rating
Charger:
Rated Voltage
Rated Frequency
Rated D.C. Output
Voltage
Rated D.C. Output
Current
IDENTIFICATION
1. Led work light
2. Forward/Reverse selector
3. Charger connection socket
4. Torque collar
5. Trigger switch
6. 1/4" female hex. drive
7. Battery charge level test button
8. Battery charge level indicator lights
9. Handle release button
10. Carry strap
UNPACKING & CHECKING
PACKAGING
Carefully remove the screwdriver from the packaging
and examine it for any sign of damage that may have
happened during shipping. Lay the contents out and
check them against the parts shown below. If any part
is damaged or missing; please contact the Customer
Service Department and do not attempt to use the
drill. The packaging material should be retained at
least during the guarantee period: in case the machine
needs to be returned for repair.
Warning! Some of the packaging materials used may
be harmful to children. Do not leave any of these mate-
rials in the reach of children.
If any of the packaging is to be thrown away, make sure
they are disposed of correctly; according to local reg-
ulations.
WHATS IN THE BOX
As well as the screwdriver; there are parts not fitted
or attached to it.
• (11) transformer charger
• (12) Case inlay with storage, containing the fol-
lowing assorted screwdriver bits:
(triax vector sum)
h
m/s
1,95
2
m/s
1,5
2
Li-Ion
V
3,6
Ah
1,5
V
100-240
Hz
50/60
V DC
5
A
0,3
25mm long 1/4" Hexagon Drive
Screwdrivers Bits Size
x5 mm 3.0
4.0
x4 No.
0
1
x4 No.
0
1
x6
T
10
15
x7
T
10
15
x7 mm 2.0
2.5
x5
IP
10
15
x3 mm 6.0
8.0 10.0
x4 No.
1
2
x4
S
0
1
x4 No.
4
6
x1
Μ
8
x1
1/4" hexagon magnetic bit holder
BASIC CORDLESS SCREWDRIVER OPERA-
TIONS
BATTERY CHARGING
i. Insert the transformer's jack plug (11.1) into the
charger connection socket (3)
ii. Plug the charger (11) to the power.
Note: over the course of the full charging cycle (ap-
proximately 5 hours), the battery charge level indica-
tor lights (7) will progressively illuminate red through
to green, indicating low to full charge accordingly. Be-
fore or during use, press the battery level test button
(8) to assess the charge level of the screwdriver's bat-
tery. The battery charge level LED indicator lights (7)
illuminate red (battery urgently requires re-charging),
through red/amber(medium charge), to green (fully
charged). Lithium-ion cells prefer small charges often.
Lithium-ion technology is lightweight and compact
due to increased capacity in comparison to other bat-
tery chemistries.
Lithium-ion cells have no 'memory effect' and a long cy-
cle life with outstanding discharge performance. Lith-
ium-ion cells suffer from a loss in capacity or thermal
runaway if over charged and will degrade if allowed to
enter deep discharge, however all of these situations
are negated due to the complex circuitry incorporat-
ed within this product. Charging must be carried out
in an environment with an ambient air temperature
between 5°C to 45°C with the transformer supplied.
To prevent overheating, do not cover the transformer.
Attention: If the cable is damaged or the non-self-re-
setting protective device is activated due to short
circuit/overload the transformer shall be scrapped. A
replacement of identical specification, design and ap-
plication shall be obtained.
FORWARD/REVERSE SELECTOR
To activate the screwdriver, press trigger (5). To change
5.0
6.0
7.0
2
3
2
3
20
25
30
40
20
25
30
35
40
3.0
4.0
5.0
5.5
6.0
20
25
30
3
4
2
3
8
10
Publicité
