F.F. Group CSC 3.6V EASY Notice Originale page 5

SERVICE
Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool is maintained.
SAFETY INSTRUCTIONS FOR CORDLESS SCREW
DRIVERS
Avoid damage that can be caused by screws, nails
f
another elements in your workpiece; remove them
before you start working.
Always check that the supply voltage is the same as
f
the voltage indicated on the nameplate of the char-
ger.
Switch off the power tool immediately when the tool
f
insert jams. Be prepared for high reaction torque that
can cause kickback. The tool insert jams when:
The power tool is subject to overload or
•
It becomes wedged in the workpiece
•
Use only accessories with an allowable speed match-
f
ing at least the highest no-load speed of the tool.
The tool/charger is not intended for use by persons
f
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowl-
edge, unless they have been given supervision or
instruction concerning use of the tool/charger by a
person responsible for their safety.
Ensure that children do not play with the tool/charger.
f
Hold the machine with a firm grip. High reaction
f
torque can briefly occur while driving in and loosening
screws.
Secure the workpiece (a workpiece clamped with
f
clamping devices or in a vice is held more securely than
by hand).
Hold power tool by insulated gripping surfaces, when
f
performing an operation where the cutting accessory
or fastener may contact hidden wiring or its own cord
(cutting accessory and fasteners contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock).
Always wait until the machine has come to a complete
f
stop before placing it down. The tool insert can jam
and lead to loss of control over the power tool.
INSTRUCTIONS FOR CHARGERS AND BATTERIES
1. BATTERY CHARGERS
a. Before charging, read the instructions.
b. For indoor use. Do not expose to rain.
2. BATTERY
a. The battery is to be disposed of safely.
b. Do not crush, open or burn the battery. Exposure
to potentially harmful materials may occur.
c. In case of fire use C0
d. Do not expose to high temperatures >45°C. Cells
may degrade at high temperatures.
e. The battery must be charged by a constant cur-
rent, constant voltage transformer.
f. Charge battery regularly in conditions between
5°C to 45°C with the specified charger designed
for this battery.
g. Store in a dry, well ventilated area within the rec-
ommended limits of 10°C to 30°C.
h. Do not use battery if it has been stored at 5°C or
less. Allow it to "normalise" at room temperature
before usage/changing.
dry chemical extinguisher.
2
i. During decommissioning remove the battery cell
for recycling separately to the product, which is
covered by the waste electrical and electronic
equipment directive. Insulate the terminals with
adhesive insulating tape to prevent a short cir-
cuit, fire or explosion occurring.
CONNECTION TO THE POWER SUPPLY
Make sure the power supply information on the ma-
chine's rating plate are compatible with the power sup-
ply you intend to connect it to. This appliance is Class
II* and is designed for connection to a power supply
matching that detailed on the rating label and compati-
ble with the plug fitted. If an extension lead is required,
use an approved and compatible lead rated for this
appliance. Follow all the instruction supplied with the
extension lead.
*Double insulated
connection as supplementary insulation is applied
to the basic insulation to protect against electric
shock in the event of failure of the basic insulation.
LITHIUM-ION MATERIAL DATA SHEET
As a substance under normal conditions of use it is not
f
considered a hazard to health. In the event of acciden-
tal release, measures to prevent spread must be ad-
hered. Do not contaminate rivers, waterways or drains.
Composition of lithium-manganese, lithium-cobalt and
f
lithium salt as the organic solvent electrolyte (non-
aqueous liquid).
Hazardous Decomposition: None during normal op-
f
erating conditions. If cell is ruptured hydrogen fluo-
ride and carbon monoxide may be released.
PRODUCT SPECIFICATIONS
INTENDED USE
This cordless screwdriver is ideal for applications such as
assembling flat pack furniture. It is intended for domes-
tic use only. Any other application is considered misuse.
TECHNICAL DATA
Article number
Model
Maximum Torque
Revolutions Per Minute
(no load)
Tool holder
Weight
Protection class
Sound emission values determined according to
EN 60745-1
Typically the A-weighted noise levels of the product are:
Sound pressure level
Sound power level
Uncertainty K
English | 5
: This product requires no earth
41312
CSC 3.6V EASY
Nm
min 180
-1
1/4" Female Hex.
kg 0,41
/ II
dB(A) 64,8
dB(A) 75,8
dB
www.ffgroup-tools.com
4
3