Publicité
Les langues disponibles
Les langues disponibles
FAILURE TO OBSERVE THESE WARNINGS COULD RE SULT IN IN JU RY.
• During
sol vents can be forcefully expelled from
fluid and air passages. Some solvents can
cause eye injury.
• Be sure all persons in the area are
wearing im pact-resistant eye and face
protection.
• Even small projectiles can in jure eyes and cause
blind ness.
• Air under pressure can cause severe injury. Al ways
shut off air supply, drain hose of air pres sure and
dis con nect tool from air supply when not in use, be fore
chang ing ac ces so ries or when mak ing
HVLP
re pairs. Nev er di rect air at your self or
anyone
cause serious injury. Al ways check for
damaged or loose hoses and fit tings.
Never use quick change cou plings at tool.
They add weight and could fail due to vi bra tion. In stead,
add a hose whip and con nect cou pling be tween air
sup ply, and hose whip, or be tween hose whip and leader
hose. Do not ex ceed max i mum air inlet pres sure of 50
PSI.
• Always use tool a safe distance from other peo ple in
work area.
• Maintain tools with care. Keep tools clean and oiled
for best and safest performance. Follow in struc tions for
lu bri cat ing and chang ing ac ces so ries. Wiping or clean ing
rags and other flam ma ble waste materials must be placed
in a tight ly closed metal con tain er and disposed of later in
the prop er fash ion.
• Do not wear loose or ill-fit ting clothing, re move
watch es and rings.
• Do not over reach. Keep prop er footing
and bal ance at all times Slip ping, Trip ping
and Falling can be a ma jor cause of se ri-
ous in ju ry or death. Be aware of excess
hose left on the walk ing or work sur face.
• Do not force tool. It will do the job better and safer at
the rate for which it was de signed.
• Do not abuse hoses or con nec tors. Never carry
tool by the hose or yank hose to dis con nect from air
sup ply.
Keep
hoses
edg es. Check hoses for weak or worn
condition
cer tain that all con nec tions are se cure.
• High sound levels can cause per ma nent
hear ing loss. Protect your self from noise.
Noise levels vary with work sur face. Wear
SX80B
SX80B_082906.indd 2
▲ WARNING!
!
cleaning
and
flushing,
else.
Whip ping
hos es
from
heat,
oil
and
sharp
before
each
use,
mak ing
ear pro tec tors.
• When possible, secure work with clamps or vise so both
hands are free to op er ate tool.
• Repetitive work motions, awk ward po si tions and ex po sure
to vibration can be harm ful to hands and arms.
• Avoid inhaling dust or han dling de bris from work
processes which can be harmful to your health.
• Operators
and
phys i cal ly able to handle the bulk, weight and powerof this
tool.
• This tool is not intended for us ing in ex plo sive at mospheres
and is not insulated for contact with electric power sources.
• Solvent and coatings can be highly
flam ma ble or com bus ti ble especially
can
when sprayed. Adequate exhaust must be
pro vid ed to keep air free of ac cu mu la tions
of flam ma ble vapors.
• Smoking must never be allowed in the spray area.
• Fire extinguishing equipment must be present in the spray
area.
• Never spray near sources of ignition, such as pilot lights,
welders, etc.
• Halogenated hydrocarbon sol vents — for example;
me th yl ene
chloride,
with the alu mi num that might be used in many system
com po nents. The chemical re ac tion caused by these solvents
reacting with aluminum can be come violent and lead to an
equip ment explosion. Guns with stain less steel fluid
passages may be used with these sol vents. How ev er, aluminum
is widely used in other spray ap pli ca tion equipment - such as
material pumps, cups and reg u la tors, valves, etc. Check
all other equipment items be fore use and make sure they
can also be used safely with these solvents. Read the
label or data sheet for the ma te ri al you intend to spray. If in
doubt as to whether or not a coating or cleaning ma te ri al is
com pat i ble, contact your ma te ri al supplier.
• Sprayed materials may be harm ful
if in haled, or if there is contact with
the skin. Adequate exhaust must
be pro vid ed to keep the air free of
ac cu mu la tions of toxic ma te ri als.
Use a mask or res pi ra tor when ev er there is a chance
of in hal ing sprayed ma te ri als. The mask must be
com pat i ble with the material being sprayed and its
con cen tra tion.
2
maintenance
per son nel
must
are
not
chem i cal ly
compatible
be
rev. 08/29/06
9/5/06 1:38:13 PM
Publicité
