Publicité
Les langues disponibles
Les langues disponibles
4. Once the motorcycle is secured with the tie-downs, raise the motorcycle to the desired work height and make sure the locking arms are engaged
with the notches.
LOWERING A MOTORCYCLE OR ATV:
1. Make sure vehicle is properly balanced on lift before removing any additional support equipment.
2. Have one person grab the handle bars of the vehicle in preparation for its lowering and eventual removal from the lift.
3. Follow step 3 under GENERAL INSTRUCTIONS to lower the load.
4. While one person is still stabilizing the motorcycle in a vertical position, the other person should remove the tie down's from the motorcycle and tie
down loops on the lift rails. The motorcycle's kickstand should be pointed down and ready to make contact with the ground. After the tie downs
are removed, lower the motorcycle all the way to the ground so the lift rails clear the motorcycle frame.
5. Slide the lift out from underneath the vehicle.
PREVENTATIVE MAINTENANCE
This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death.
1. Always store the lift in a well protected area where it will not be exposed to inclement weather, corrosive vapors, abrasive dust, or any
other harmful elements. The jack must be cleaned of water, snow, sand or grit before using.
2. Lubricate all moving parts and joints monthly with the exception of the hydraulic jack. Use a waterproof lubricating grease.
3. Visual inspection should be made before each use of the lift, checking for leaking hydraulic fluid and damaged, loose or missing parts.
Each lift must be inspected by a manufacturer's repair facility immediately, if subjected to an abnormal load or shock. Any lift which
appears to be damaged in any way, is found to be badly worn, or operates abnormally MUST BE REMOVED FROM SERVICE until
necessary repairs are made by a manufacturer's authorized repair facility. It is recommended that an annual inspection of the lift be made
by a manufacturer's authorized repair facility and that any defective parts, decals or warning labels be replaced with manufacturer's
specified parts.
A list of authorized repair facilities is available from the manufacturer.
4. It should not be necessary to refill or top off the reservoir with hydraulic fluid unless there is an external leak. An external leak requires
immediate repair which must be performed in a dirt-free environment by an authorized service center.
5. Every jack owner is responsible for keeping the jack labels clean and readable. Use a mild soap solution to wash external surfaces of
the jack but not any moving hydraulic components.
TROUBLESHOOTING
PROBLEM
1. Unit will not lift load.
2. Unit will not sustain load or feels "spongy" under load.
3. Unit will not lift to full height.
4. Unit still does not operate.
LIMITED WARRANTY
SUNEX INTERNATIONAL, INC. WARRANTS TO ITS CUSTOMERS THAT THE COMPANY'S SUNEX TOOLS® BRANDED
PRODUCTS ARE FREE FROM DEFECTS IN WORKMANSHIP AND MATERIALS.
Sunex International, Inc. will repair or replace its Sunex Tools® branded products which fail to give satisfactory service due to defective workmanship or materials, based
upon the terms and conditions of the following described warranty plans attributed to that specific product.
This product carries a ONE-YEAR warranty. During this warranty period, Sunex Tools will repair or replace at our option any part or unit which proves to be defective in
material or workmanship.
Other important warranty information
This warranty does not cover damage to equipment or tools arising from alteration, abuse, misuse, damage and does not cover any repairs or replacement made by
anyone other than Sunex Tools or its authorized warranty service centers. The foregoing obligation is Sunex Tools' sole liability under this or any implied warranty and
under no circumstances shall we be liable for any incidental or consequential damages.
NOTE: Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Return equipment or parts to an authorized service center, transportation prepaid. Be certain to include your name and address, evidence of the purchase date, and
description of the suspected defect. If you have any questions about warranty service, please write to Sunex Tools. This warranty gives you specific legal rights and you
may also have other rights which vary from state to state.
Repair kits and replacement parts are available for many of Sunex Tools products regardless of whether or not the product is still covered by a warranty plan.
SHIPPING ADDRESS:
Sunex Tools
315 Hawkins Rd.
Travelers Rest, South Carolina 29690
6616
ACTION
Purge air from hydraulic system by following procedure under SETUP.
Purge air from hydraulic system as above.
Purge air from hydraulic system as above.
Contact an authorized service center.
MAILING ADDRESS:
Sunex Tools
P.O. Box 1233
Travelers Rest, South Carolina 29690
4
rev.03/15/11
Publicité
