Bimar VR20 Notice D'instructions page 11

Fax +32 030 9904733
2. Attention: for the appliance to run, the
front grill must be open (at least 45°);
manually raise the grill toward the other
one, as shown in the picture to the side:
you will hear a "click" indicating that the
appliance is in stand-by mode.
3. To operate the appliance, press the ON/OFF button (D) on the remote control or the control panel, the
NORMAL light will turn on at the minimum FAN LOW speed; to change the desired speed, repeatedly
press the SPEED button (E) and the FAN MIDDLE light (medium speed) and then the FAN HIGH light
(maximum speed) will turn on.
4. When you press the MODE button (C) on the control panel or remote control, it changes to NATURE
mode: the NATURE indicator light will turn on.
5. SLEEP mode is activated by pressing the MODE button on the control panel or remote control again:
the SLEEP indicator light turns on.
6. Pressing the COOLER button (G) on the control panel or remote control activates the function: the
COOLER indicator light turns on.
7. When you press the SWING button (B) on the control panel or remote control, the oscillation function
turns on: the SWING indicator light will turn on. To turn off oscillation, press the SWING button again.
8. When you press the IONIC button (F) on the control panel or remote control, the function is activated:
the IONIC indicator light will turn on indicating that the ionizer is working. To turn this function off,
press the key again.
9. When you press the Timer button (A) on the control panel or remote control, the function is activated:
each press of the button changes the time set; press once to start a time of 1 hour, the corresponding 1hr
light will turn on; press again to set the time to 2 hours and the corresponding 2hr light will turn on;
press it a third time to set a time of 4 hours, the corresponding 4hr light will turn on; finally, press it a
fourth time and a time of 8 hours will be set, the corresponding 8hr light will turn on. To turn this
function off, press the button again (fifth time) and no light will be on.
10. In all modes, the fan and cooler can run for a maximum of 24 hours, after which the appliance stops
automatically and goes to stand-by mode; to start it again, press the ON/OFF button.
11. To turn off the appliance and put it in stand-by mode, press the ON/OFF button on the control panel or
remote control.
12. After each use, we recommend that you empty the tank of water using the plug.
When not in use for long periods, the plug must always be removed from the socket.
CLEANING AND MAINTENANCE
Attention: before normal cleaning, remove the plug from the socket.
The appliance works best if the filters and tank are clean.
• Periodically check that the rear intake filter (11) is not clogged with dust, lint, or fibres. If it is dirty,
remove it by pressing the two tabs (12), and clean the netting with a brush or with water, being careful
not to damage it; then dry it completely and put it back in place.
• Periodically check that the honeycomb filter (20) is not dirty. If it is, remove it from its seat and clean it
with water with a little household detergent and use a soft brush to clean the external honeycombs. Be
careful not to damage the honeycombs or other parts. Rinse thoroughly under the tap water and let it
drip dry before replacing it in its seat and check that no electrical parts are wet. If they are, dry
carefully and completely.
• To clean the tank and ice bricks, use water with a little detergent and a soft cloth and wash carefully.
Rinse the tank and bricks under running water and let drip dry before replacing them in their seat.
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Bimar (Italy).
The pages must be reproduced and folded in order to obtain
a booklet A5 (+/- 148.5 mm width x 210 mm height). When
folding, make sure you keep the good numbering when you
turn the pages of the I/B. Don't change the page numbering.
Keep the language integrity.
11 32
/
Assembly page 11/24