Bimar VR20 Notice D'instructions page 10

Fax +32 030 9904733
- make sure that the main unit is in the correct position (control panel on top) and that its front is aligned
with the front of the tank (straight side).
- make sure that the water hose stays (15) inside the tank and without kinks.
- check that the 2 pins (13) are fully out and "engaging" the edge of the tank.
- check that the electric cord is outside of the tank and is not kinked.
- make sure the unit and tank are correctly connected.
- after placing the appliance in its more or less permanent position, check that it is stable on the
supporting surface (which, of course, must be horizontal), and lock the rear wheels by depressing the
latch in order to prevent it from moving inadvertently.
• The air is sucked in through the two filters in the rear of the main unit: the outer one made of synthetic
material is washable and catches the larger particles (dust, fluff, lint, etc.); it attaches using the 2 tabs on
the top. The internal honeycomb filter of natural fibres is sprayed with water by the pump and cools the
air passing through it: the water drain must be pointing downwards and must be inserted in the
rectangular slot.
• Insert the 2 AAA batteries in the remote control, respecting their polarity. Open the rear door, insert
them and then close it.
Attention: the appliance can be used only when completely and correctly assembled.
USE
Attention: always unplug the appliance before you assemble, and insert the water inside the tank.
This appliance is intended for home ventilation and cooling. With the "cooler" function, the appliance
adds micro-droplets of water to the air, which evaporate and cool it: the drier the air, the more effective it
is and its effectiveness decreases as the relative humidity of the air (RH) increases. Above an RH of 75%,
the cooling effect is negligible. The honeycomb filter (20) is constantly sprayed with water and the air
picks up micro-droplets as it passes through it. The "cooler" function only works with water in the tank
between the min and max values.
These are the functions of the appliance:
- 0/1 main switch (2), turns the appliance on and off
- stand-by function (ON/OFF button) activates or stops the functions.
- normal ventilation/sleep/nature (Mode button): Normal = constant ventilation; Sleep = ventilation
increases and decreases and stops alternately; Nature = ventilation alternately changes intensity like a
breeze.
- intensity Min/Med/Max. (Speed button): adjusts the speed of the above ventilation modes. Min =
minimum speed, Med = medium speed, Max = maximum speed.
- cooling (Cooler button): turns the cooling function on and off and, in effect, the pump that sprays the
honeycomb filter.
- timer (Timer button): turns the timer on and off (up to 8 hours with intervals of 1 hour) and stops the
machine when the time elapses. If the timer is not on, the appliance runs continuously until it is manually
turned off but it turns of anyway after running for 24 hours: after this time, just press the ON button to
continue ventilation/cooling.
- oscillation (Swing button): turns the automatic right-left oscillation on and off.
- Ionizer (Ion button): turns the ionizer function on and off, which produces a stream of negative ions.
All the above functions are indicated by a lighted symbol on the control panel in addition to an LED that
indicates "appliance connected".
Before each use, check that the appliance is in good condition and that the power cord is not damaged: if
it is, replace it.
The functions of the fan can be turned on and off using either the button pad on the control panel (1) or
the remote control (3). The remote control must be pointed at the control panel. Insert the plug into the
outlet.
1. Turn the main switch (2) at the side to "I".
Copies of the I/B. Please reproduce them without any
changes except under special instruction from Bimar (Italy).
The pages must be reproduced and folded in order to obtain
a booklet A5 (+/- 148.5 mm width x 210 mm height). When
folding, make sure you keep the good numbering when you
turn the pages of the I/B. Don't change the page numbering.
Keep the language integrity.
10 32
/
Assembly page 10/24