Picture Options
✎
In PC mode, you can only make changes to the
Tone, Size , and Auto Protection Time.
Picture Options
Colour Tone
: Normal
Size
: Auto Wide
Screen Mode
: 16:9
Digital Noise Filter
: Auto
MPEG Nosie Filter
: Auto
HdMI Black level
: Normal
Film Mode
: Off
▼
U Move E Enter R return
Colour Tone (Cool / Normal / Warm1 / Warm2)
■
✎
Warm1
or Warm2 will be deactivated when the
picture mode is Dynamic.
✎
Settings can be adjusted and stored for each
external device connected to an input on the TV.
: Your cable box/satellite receiver
Size
■
P.MODE
may have its own set of screen
sizes as well. However, we highly
recommend you use 16:9 mode most
of the time.
Auto Wide: Automatically adjusts the
picture size to the 16:9 aspect ratio.
16:9 : Adjusts the picture size to 16:9 for DVDs or wide
broadcasting.
Wide Zoom: Magnifies the picture size more than 4:3.
✎
Adjusts the Position by using
Zoom: Magnifies the 16:9 wide pictures vertically to fit
the screen size.
✎
Adjusts the Position or Size by using
4:3 : The default setting for a movie or normal broadcasting.
✎
Do not watch in 4:3 format for a long time. Traces
S.MODE
of borders displayed on the left, right and centre
of the screen may cause image retention(screen
burn) which are not covered by the warranty.
Screen Fit: Displays the full image without any cut-off
when HDMI (720p / 1080i / 1080p) or Component
(1080i / 1080p) signals are inputted.
✎
NOTE
x
After selecting
Screen Fit in HDMI (1080i/1080p) or
Component (1080i/1080p) mode, you may need to
centre the picture:
1. Press the ◄ or ► button to select Position.
2. Press the ENTERE button.
3. Press the ▲, ▼, ◄ or ► button to move the picture.
x
Depending on the input source, the picture size
options may vary.
x
The available items may differ depending on the
selected mode.
Colour
►
■ Screen Mode (16:9 / Wide Zoom / Zoom / 4:3):
■
■
■
■
▲, ▼ buttons.
▲, ▼ button.
■
■
Picture Reset (OK / Cancel)
Resets your current picture mode to its default settings.
x
In PC mode, only
16:9 and 4:3 modes can be
adjusted.
x
Settings can be adjusted and stored for each
external device connected to an input of the TV.
x
If you use the
Screen Fit function with HDMI 720p
input, 1 line will be cut at the top, bottom, left and
right as in the overscan function.
Available only when picture size is set to Auto Wide.
You can determine the desired picture size at the 4:3
WSS (Wide Screen Service) size or the original size.
Each European country requires different picture size.
✎
Not available in PC, Component or HDMI mode.
Digital Noise Filter (Off / Low / Medium / High / Auto
/Auto Visualisation): When the broadcast signal is
weak, some static and ghosting may appear. Select one
of the options until the best picture is displayed.
Auto Visualisation: When changing analogue channels,
displays signal strength.
✎
Only available for analogue channels.
✎
When bar is green, you are receiving the best
possible signal.
MPEG Noise Filter (Off / Low / Medium / High /
Auto): Reduces MPEG noise to provide an improved
picture quality.
✎
Disabled under PC mode.
HDMI Black Level (Normal / Low)
level on the screen to adjust the screen depth.
✎
Available only in HDMI mode (RGB signals).
Film Mode (Off / Auto1 / Auto2)
automatically sense and process film signals from all
sources and adjust the picture for optimum quality.
✎
Available in TV, AV, COMPONENT (480i / 1080i)
and HDMI (480i / 1080i).
100Hz Motion Plus (Off / Clear / Standard / Smooth /
Custom / Demo) : Removes drag from fast scenes with
a lot of movement to provide a clearer picture.
✎
If you enable
100Hz Motion Plus, noise may
appear on the screen. If this occurs, set 100Hz
Motion Plus to Off.
Blur Reduction: Adjusts the blur reduction level from
video sources.
Judder Reduction: Adjusts the judder reduction level
from video sources when playing films.
Reset: Reset the custom settings.
Auto Protection Time (2 hours/4 hours/8 hours/10
hours/ Off) : If the same image remains on the screen,
Auto Screen Burn Protector will work.
: Selects the black
: Sets the TV to
15
English