Nice Neomat T Instructions Et Avertissements Pour L'installation Et L'utilisation page 8

– At the sun underthreshold command by a sensor, the motor will carry out the closure of
the awning.
Special cases:
– The sun is not a blocking event, or better the user may at any time decide to close, open
or adjust the opening of the awning as required.
– When the climate sensor sends the sun underthreshold command, in any case the
motor will carry out the closure of the awning.
Response to rain:
– At the start of rain command by a climate sensor, the motor will carry out a lowering or
raising movement according to the direction previously selected, blocking the command
logic related to the sun.
– At the end of rain command, the motor restores the operation logic of the sun.
Special cases:
– Rain is not a blocking event, or better the user may at any time decide to close, open or
adjust the opening of the awning as required.
– When interacting with the awning by opening or closing it during the raining phase, each
15 minutes the motor will restore the initial condition of the event (awning open or closed
according to the direction).
– Rain prevails over the sun.
Response to wind:
– At the wind overthreshold command, the motor will carry out the closure of the awning
by blocking the motor commands and the sun/rain operation logic.
– At the wind underthreshold command, the motor restores the operation logic of the sun/
rain unblocking the automation.
Special cases:
– Wind is a blocking event, or better it blocks the commands by the user and the sun/rain
logics to protect the awning from hypothetical breakage.
SUN ON TLC button function:
When SUN ON is activated via the remote control, the motor will immediately respond
to the climate logic related to the SUN. If the sun was active the awning will immediately
lower, while if the sun is not active nothing will happen.
4.3.6 - Programming of the "wind" weather sensor level
If a "VOLO" or "VOLO S" wind sensor is connected to the "sensors" input, the wind protection
is activated that automatically retracts the awning when the wind exceeds the programmed
level. If the level is exceeded for more than 3 seconds, a command that is the same as the
▲ button is activated and any other movement is blocked until the wind level returns below
the programmed level for more than 1 minute. There is a choice of 5 different activation levels:
1=5Km/h, 2=10Km/h, 3=15Km/h, 4=30Km/h and 5=45Km/h. (the level is factory set at No.3).
6 – English
If using the sensor "VOLO ST" or radio sensors Volo S Radio and Nemo, the wind trip
thresholds are programmed directly on the sensor (see relative instructions).
To modified the programmed level:
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A9" - Changing the activation level of the "wind" protection
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
01. Press and hold down button ■ of a previously memo-
rized transmitter until you hear a beep (after about 5 sec-
5s...
onds) then release it.
02. Slowly press button ▲ the same number of times (1, 2,
3, 4 or 5) as the desired level.
x 1 = 5 Km/h
x 2 = 10 Km/h
x 3 = 15 Km/h
x 4 = 30 Km/h
03. After a few moments you will hear a number of beeps
x 5 = 45 Km/h
equal to the required level.
x 1 = 5 Km/h
x 2 = 10 Km/h
x 3 = 15 Km/h
x 4 = 30 Km/h
04. Press and release button ■ to confirm.
x 5 = 45 Km/h
If at point 3 you don't here the number of beeps equal to the desired level, simply do
not press anymore buttons and wait a few seconds for it to finish without changing the
level.
4.3.7 - Programming of the "sun" weather sensor level
If a "VOLO S" sun sensor is connected to the "sensors" input, the sun automation is acti-
vated that automatically lowers the awning when the "sun" exceeds the programmed level.
If the level is exceeded for more than 2 minutes, a command that is the same as the ▼
button is activated and if the sun drops below the programmed level for 15 minutes, a
command is activated that is the same as button ▲.
There is a choice of 5 different "sun" activation levels: 1=5Klux, 2=10Klux, 3=15Klux,
4=30Klux and 5=45Klux (the level is factory set at No. 3).
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Table "A10" - Changing the activation level of the "sun" automation
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
If using the sensor "VOLO ST" or radio sensors Volo S Radio and Nemo, the sun trip
thresholds are programmed directly on the sensor (see relative instructions).
01. Press and hold down button ■ of a previously memo-
5s...
rized transmitter until you hear a beep (after about 5 sec-
onds) then release it.