Installation And Connection; Ac Power Connection; Signal Cable Connection; Connecting To Any Ibm Vga Compatible System - Mitsubishi Diamond Pro 2060u Mode D'emploi

3
3
INSTALLATION AND
CONNECTION
On the back of the monitor three kinds of plug-in connec-
tions are provided: AC power connector for the AC input,
two DB9-15P connectors for video signal input, and USB
ports for USB communication.
3.1

AC Power Connection

One end of the AC power cord is connected to the AC
power connector on the back of the monitor. The other end
is plugged into a properly grounded three-prong AC outlet.
The monitor's auto-sensing power supply can automati-
cally detect 100-120V AC or 220-240V AC and 50 or 60Hz.
3.2

Signal Cable Connection

The DB9-15P(VGA) connector is provided for compatible
analog RGB outputs from your computer. Apple Macintosh
computers can also be interfaced with using the optional
Mitsubishi Macintosh adapter AD-A205.
3.2.1 Connecting to Any IBM VGA Compatible Sys-
tem
Figure 5 shows the SC-B110 cable connection to the Video
Graphics Array (VGA) port in an IBM Personal System/2
series, or any VGA compatible system.
1. Power off, both the monitor and the computer.
2. Connect the one end of the SC-B110 cable to the
DB9-15P connector on the VGA controller card.
3. Connect the other end of the SC-B110 cable to the
DB9-15P receptacle on the back of the monitor.
4. Power on the monitor, then the computer.
5. After using the system, power off the monitor, then
the computer.
VGA
Compatible
System
Connect to Analog RGB
Connector (D-Sub 15P)
Figure 5
CAUTION
The socket-outlet shall be installed near the equipment
and shall be easily accessible. During servicing, discon-
nect the plug from the socket-outlet.
®
SIGNAL-B SIGNAL-A
Cable
SC-B110
-1-6 -

3.2.2 Connecting to An Apple Macintosh Computer

Figure 6 shows the SC-B110 cable and AD-A205
Adapter(option) to the video port in an Apple Macintosh.
For Macintosh Adapter AD-A205, contact your dealer.
1. Power off, both the monitor and the computer.
2. Set the DIP switches of Macintosh Adapter according
to the setting chart.
(See Section 7.3 Optional Macintosh Adapter AD-
A205 Settings)
3. Connect the 15-pin (DB-15P) end of the AD-A205
Adapter to the straight 15-pin connector on the
Macintosh video port on the computer or on the video
board.
4. Connect the sub-miniature 15-pin (DB9-15P) end of
the AD-A205 Adapter to the SC-B110 cable.
5. Connect the other end of the SC-B110 cable to the
DB9-15P receptacle on the back of the monitor.
6. Power on the monitor, then the Macintosh.
7. After using the system, power off the monitor, then the
Macintosh.
Apple Macintosh
Computer
5 0 2 - A D A
1 D-SUB15P
O N N O
6 5 4 3 2 1
H I S B I U S I T M
Macintosh Adapter
AD-A205 (Option)
Figure 6
NOTE
• For the Apple Macintosh Computers having a VGA
compatible port, steps 2 through 4 are not necessary.
Connect the end of the signal cable to the port directly.
• In case of Apple Macintosh G3 series, use "Control
Panel" of "Apple Menu" when selecting a resolution.
If select the resolution from "Control Bar", no screen may
be displayed and the computer may freeze.
SIGNAL-B SIGNAL-A
Cable
SC-B110
DB9-15P
2