Dorel Maxi-Cosi EasyFix Mode D'emploi & Garantie page 7

EN
A. Installing
IMPORTANT!
Make sure the Isofix connectors are retractedT
• Press the central button on the support leg and pull
14
the support leg forward as far as possibleT
IMPORTANT!
Secure any fold-down seatsT
IMPORTANT!
On some seats, the belts are fitted so far forward
that proper installation is not possibleT
If this is the case, try another seat (see section 9:
Car fitting list)T
• Place the EasyFix on the seat of the car with the
15
support leg folded outT
• Open the blue belt clamp by pulling the lever upT
16
Pass the shoulder and lap belt together through
the belt openingT
• Pass the seat belts between the base and the blue
17
belt clamp and then through the second belt
openingT
• Insert the seat belt into the belt buckle of the carT
17
NOTE!
Make sure that the seat belt is pulled tight
and is not twistedT
• Fasten the belt clamp by pushing the lever downT
18
• Check that it is fastened correctly by pulling on
the EasyFixT
14
B. Adjusting the length of the support leg
• See section 3T1, point B: "Adjusting the length
of the support leg"T
Checklist ...
To ensure the optimum safety of your child, check
the following after installation:
• The seat belt is as tight as possible and not twistedT
• The two belt parts pass through the belt openings
in the base and under the blue belt clampT
• The support leg is fully folded outT
• The indicator at the base of the support leg is
completely greenT
• In some cases the EasyFix may not be fully
supported by the car seat, but entirely by the
support legT
• The EasyFix as a whole has been installed in the
car in a secure and stable manner by pulling on the
EasyFixT
C. Removing the EasyFix
• Restore the support leg to its start position by
19
pressing the control button and sliding the support
leg upwardsT
• Loosen the seat belt and open the blue belt clampT
20
• Take the seat belt out from between the base and
21
the blue belt clamp and fasten the belt clampT
• Remove the EasyFix from the carT
4. INSTALLING AND REMOVING
THE CABRIOFIX
A. Installing the CabrioFix
• Position the CabrioFix facing backwards (with the
22
back facing the direction of driving) on top
of the EasyFixT The carrying handle should be in the
upright positionT
• Click the CabrioFix with its 2 spindles onto the
23
anchor points of the EasyFixT
NOTE!
A clear click should be audible and the indicators
24
should now be completely on greenT
NOTE!
Under no circumstances should this product
be used if the indicator remains on red.
Carry out the above actions againT In case
of doubt or if you have any questions, contact
the manufacturerT
• Check that CabrioFix has been installed correctly
by pulling on itT
To install the child in the CabrioFix or to remove him/
her, see the CabrioFix user instructionsT The optimum
safety of your child is only guaranteed if the CabrioFix
is used correctlyT It is therefore important that you take
the time to read these instructions through carefullyT
However, if you do not have these instructions, contact
our service point in your country or download
the necessary information from our internet site:
wwwTmaxi-cosiTcomT
EN
B. Removing the CabrioFix
• Unlock the CabrioFix by pulling the release lever
25 26
upwards and at the same time forwardsT
This releases the spindles from the anchor points
and take the CabrioFix out of the EasyFixT
5. MAINTENANCE
IMPORTANT!
Always remove the EasyFix from the car before
carrying out any of the followingT
• Use lukewarm water, soap and a rag to clean the
plastic parts of the EasyFixT Do not use abrasive
cleanersT
IMPORTANT!
Never use lubricants, not even for the moving parts
on the EasyFixT
15