Sunex Tools SX959A Instructions De Fonctionnement page 2

This
Important Safety Information.
Read
CaRefULLy
INfORMaTION
THIS TOOL.
• Always operate, inspect and maintain this
tool in accordance with American National
Standards Institute Safety Code of Portable
Air Tools (ANSI B186.1) and any other
applicable safety codes and regulations.
• For safety, top performance and maximum
durability of parts, operate this tool at 90
psig/6.2 bar max air pressure with 3/8"
diameter air supply hose.
• Always wear impact-resistant eye and face
protection when operating or performing
maintenance on this tool. Always wear
hearing protection when using this tool.
• High sound levels can cause permanent
hearing loss. Use hearing protection as
recommended by your employer or
OSHA regulation.
• Keep the tool in efficient operating
condition.
• Operators and maintenance personnel
must be physically able to handle the bulk,
weight and power of this tool.
• Air under pressure can cause severe injury.
Never direct air at yourself or others.
Always turn off the air supply, drain hose
of air pressure and detach tool from air
supply before installing, removing or
adjusting any accessory on this tool, or
before performing any maintenance on this
tool. Failure to do so could result in injury.
Whip hoses can cause serious injury.
Always check for damaged, frayed or loose
hoses
immediately. Do not use quick detach
couplings at tool. See instructions for
correct set-up.
• Air powered tools can vibrate in use.
Vibration,
uncomfortable positions over extended
periods of time may be harmful to your
hands and arms. Discontinue use of tool if
discomfort, tingling feeling or pain occurs.
Seek medical advice before resuming use.
• Place the tool on the work before starting
the tool. Do not point or indulge in any
horseplay with this tool.
SX959A/SX959A-2: Parts Breakdown & Operating Manual
WARNING
WARNING!
WARNING
FAILURE TO OBSERVE THESE WARNINGS
COULD RESULT IN INJURY.
ADVERTENCIA
Instruction Manual Contains
ADVERTENCIA
THIS INSTRUCTION
aNd UNdeRSTaNd
BefORe OpeRaTINg
AVERTISSEMENT
AVERTISSEMENT
and fittings, and
repetitive motions
MaNUaL
aLL
replace
or
2
• Slipping, tripping and/or falling while
operating air tools can be a major cause
of serious injury or death. Be aware of
excess hose left on the walking or
work surface.
• Keep body working stance balanced and
firm. Do not overreach when operating
the tool.
• Anticipate and be alert for sudden changes
in motion during start up and operation of
any power tool.
• Do not carry tool by the hose. Protect the
hose from sharp objects and heat.
• Tool shaft may continue to rotate briefly
after throttle is released. Avoid direct
contact with accessories during and after
use. Gloves will reduce the risk of cuts
or burns.
• Keep away from rotating end of tool.
Do not wear jewelry or loose
clothing. Secure long hair. Scalping can
occur if hair is not kept away from tool
and accessories. Choking can occur if
neckwear is not kept away from tool
and accessories.
• Impact wrenches are not torque con t rol
devices. Fas t en e rs with spe c if i c torque
re q uire m ents must be checked with
suit a ble torque measuring de v ic e s after
in s tal l a t ion with an im p act wrench.
• Use only impact wrench sock e ts and
ac c es s o r ies on this tool. Do not use hand
sock e ts and ac c es s o r ies, as they may be
damaged or cause damage to the equipment
or operator.
• Do not lubricate tools with flammable or
volatile liquids such as kerosene, diesel
or jet fuel.
• Do not force tool beyond its rated capacity.
• Do not remove any labels. Replace any
damaged labels.
• Use accessories recommended by
Sunex Tools®.
Rev. 10/13/09