Table Des Matières; Detection; Mounting; Ambient Temperature - OJ Electronics ETO2 Instructions

English / Instruction
The product carries a manufacturer's warranty if
installed in accordance with these instructions
and current regulations.
If the product has been damaged in any way,
e.g. during transport, it must be inspected and
checked by authorised personnel before being
connected to the power supply.
TECHNICAL DATA
Thermostat ETO2-4550:
Designed for indoor mounting only!
Supply voltage .... 115/240 V AC ±10%, 50-60 Hz
Supply voltage for ETOG/ETOR
heating (SMPS) ...............................28 V DC, 8 VA
3 output relays
(potential-free contact, NO) .....................3 X 16 A
Alarm relay (potential-free contact, NO) . max. 5 A
Control signal to actuator
(mixing valve) ....................................... 0-10 V DC
Supply voltage to actuator
(mixing valve) ..........max. 48 V AC/DC / max. 2 A
On/off differential ................................ 1.8°F / 1°C
Temperature range ............. -4/+50°F / -20/+10°C
Ambient temperature ............. 32/122°F / 0/+50°C
Ambient air humidity ............................... 10-95%
Enclosure rating ............................................ IP 20
Weight ......................................................... 600 g
Dimensions H/W/D ........................90/156/45 mm
Type ..................................................................1B
Control pollution degree .................................... 2
Rated impulse voltage ................................... 4 kV
Ground sensor - type ETOG-55:
Designed to be embedded in outdoor surfaces.
Detection .....................Moisture and temperature
Mounting .................................. Outdoor surfaces
Enclosure rating ............................................ IP 68
Ambient temperature ...... -57/+158°F / -50/+70°C
Dimensions .....................................H32, Ø60 mm
Ground sensor - ETOG-56/ETOK-1:
Designed to be embedded in outdoor surfaces.
Detection ....................Moisture and temperature
Mounting ................................. Outdoor surfaces
Enclosure rating ............................................ IP 68
Ambient temperature ...... -57/+158°F /-50/+70°C
Dimensions, sensor .......................H32, Ø60 mm
4
Dimensions, tube ........................H78, Ø63.5 mm
Gutter sensor - type ETOR-55:
Designed to be mounted in gutter or downpipe.
Is used together with outdoor sensor type ETF-
744/99.
Detection ................................................ Moisture
Mounting ............................... Gutter or downpipe
Enclosure rating ............................................ IP 68
Ambient temperature ...... -57/+158°F / -50/+70°C
Dimensions H/W/D ........................105/30/13 mm
Outdoor sensor - ETF-744/99:
Detection .......................................... Temperature
Mounting ....................................................... Wall
Enclosure rating ............................................ IP 54
Ambient temperature ...... -57/+158°F / -50/+70°C
Dimensions H/W/D ..........................86/45/35 mm
Water pipe sensor - ETF-522:
Detection .......................................... Temperature
Mounting ................................... Strapped to pipe
Enclosure rating ............................................ IP 54
Ambient temperature .... -40/+248°F / -40/+120°C
Dimensions .................................... Ø6.5, L50 mm
failure - regardless of sensor type.

SENSOR INSTALLATION

Ground sensor - ETOG, figs 1+3:
For installation in outdoor surfaces where ice
and snow are a regular problem. The sensor
must be embedded horizontally with its top flush
with the surrounding surface.
The sensor cable must be installed in
accordance with current regulations.
NOTE: We strongly recommend the use of
cable pipes in order to protect the sensor cable.
Detailed installation instructions are supplied
with the sensor.
With ETOG-55, use the accompanying installation
plate.
With ETOG-56, use the ETOK-1 mounting kit.
© 2020 OJ Electronics A/S
NOTE: The snow and ice melting system
is deactivated in the event of sensor
NOTE: Remove the installation plate from
ETOG-55 before initial start-up.
Type ETO2