Removing The Seat Cover - Be Cool STORM isofix Instructions

CONVERTING FOR CHILDREN IN
6
GROUP II (15-25 kg)
1 It is recommended that you use the 5-point
harness for as long as possible.
Try removing the booster cushion as this could
allow you to use the seat in group I configura-
tion for longer.
When your child has outgrown the group I [9-
18kg] configuration or you wish to use the seat
for a child 15-25kg, then you will need to con-
vert the child car seat to group II mode.
You will need to remove the child car seat's
integral 5-point harness.
Press button (A) and pull up on the shoulder
straps (not the shoulder pads) to completely
loosen the shoulder straps much as possible.
IMPORTANT: DO NOT pull the shoulder pads.
2 Adjust the shell to its most reclined position.
Pull the recline adjuster handle under the
front of the shell and whilst holding it, pull the
shell forwards to its most reclined position.
Remove the installation bar (C) by pulling the
3
lock (D) up, on the top right hand side of the
shell.
4
Pull and hold the shell forward.
Unhook the shoulder pad straps from shoul-
5
der pad connector (E). Unhook the shoulder
harness straps from yoke (F).
Pass the shoulder straps through the slots in
the back of the shell (G).
Locate the two metal retainer buckles (H) un-
6
der the seat cover at points (1) and (2).
Pass the metal buckles on the waist harness
from the front of the shell, through the inner
slots (I) on the back of the shell and back out
the outer slots (J), to the front to remove the
harness.
If your child does not need the booster cush-
7
ion (K) if can be removed.
To remove the crotch strap, ensure the child
car seat is in a fully reclined position.
Push the crotch strap down through the slot
and hold it there, allowing the strap to slacken
on the underside of the child car seat. Whilst
holding the strap locate the metal retainer
buckle underneath the car seat shell and pass
it through the bottom of the seat and remove
the crotch strap.
Return the shell to its original position and re-
insert the installation bar (L) and secure the
lock (M).
7
INSTALING FOR GROUP II (15-25 kg)
Ensure that you have first removed the child car
seat's integral 5-point harness, following the
steps under 'Removing the 5-point harness'.
Position your child in the child car seat, place
the diagonal section of the seatbelt through the
INSTRUCCIONES
GEBRAUCHSANWEISUNG
INSTRUÇÕES
diagonal seatbelt guide (A) and the waist belt
across the child's lap and through belt guide (B).
Finally fasten the seatbelt buckle (C).
WARNING: The child car seat should always
be buckled in and secured, whether a child is
seated in it or not!
8

REMOVING THE SEAT COVER

The seat cover is a safety feature. Never use the
child car seat without its cover.
The seat covers can be removed for cleaning
(see "Maintenance and cleaning" p18). You will
need a phillips screwdriver.
If not already removed then remove the harness
straps, crotch strap, head cushion and base
cushion (see 'Converting for children in group II
[15- 25kg]', page 11-13).
Turn the child car seat on its side and using a
Phillips screwdriver, unscrew the two screws on
each side of the shell holding the belt guides (A)
in place. Put the belt guides and screws safely to
one side for later.
Remove the two small side covers (B) by grasing
the elastic band and pulling each cover off.
The main cover is held in place by a series of
hooks(C) located on the back and underside of
the shell. Unhook the cover's elastic from the
hooks. Work the cover from under the strap
hooks (D) and remove.
REPLACING THE SEAT COVER AND
9
HARNESS
1
Place the cover over the child car seat and
stretch the elastic over the shell, taking care as
you work the cover over and around the plastic
parts. Once in place on the back and underside
of the shell.
Stretch the two side covers (B) back over the
side panels.
2
The belt guides have a narrow point (1) and a
wider point (2).
Reattach the belt guides (C) ensuring they are
put on correctly shown.
Reattach the two screws on each side.
6
Attention: Be careful to not over-tighten the
screws as this could cause damage.
Adjust the shell to its most reclined position.
4
Pull the recline adjuster handle under the front
• INSTRUCTIONS
• INSTRUCTIONS
• ISTRUZIONI
33