Be Cool STORM isofix Instructions page 32

GB
1
POSITIONING THE SEAT
1) The car seat can be used with isofix anchors
and top tether for group 1 (9-18kg child).
2) The car seat must be used with an ISOFIX
anchor and top tether as well as a 3-point seat
belt for group 2 (15-25kg child).
The child car seat can be secured in a forward-
facing position in the rear seats of the vehicle
by using the existing seatbelts. However, on
some seats, if the installation is not properly
secured, we sug upright gest you try another
seat in your vehicle.
WARNING: Never use in a seat with an active
airbag.
2
FIVE-POSITION SEAT RECLINE
The child car seat can be used in five differ-
ent seat positions, from seated to a reclined
sleeping position. Pull the recline adjuster
handle under the front of the shell and whilst
holding it, pull the shell forwards or back-
wards, release the handle on your required
position when hearing a distinct click.
3
INSTALLING FOR GROUP I (9_18 kg)
Place the child car seat on a suitable passen-
1
ger seat. Adjust the child car seat to its most
reclined position.
Pull the recline adjuster handle under the
front of the shell and whilst holding it, pull the
shell forwards to its most reclined position.
a) Place the car seat on the vehicles seat.
2
b) Rotate the adjuster button in an anti-clock
wise direction(A),and pull the isofix
anchors outwards as far as it goes, make sure
it cannot be pushed back (B)
c) Push the car seat towards the back of vehi-
3
cles seat(A)
d) Match the isofix anchors to the vehicles an-
choring point until you hear a "click"(B)
e) Rotate the adjuster button in an anti-clock
wise direction(C),and push the car seat to the
back of vehicles seat as much as possible(D)
4 f) Hook the top tether up and pull as tight as
possible(A)
4
PLACING YOUR CHILD IN THE SEAT
GROUP I (9-18 kg)
1
Ensure that you have first installed the child
cat seat correctly, following the steps under
'Installing for Group I [9-18kg]', Press button
(B) and pull up on the shoulder straps (not the
shoulder pads) to lossen the straps.
Press button (A) and unfasten the harness.
IMPORTANT: DO NOT pull the shoulder pads.
2 Place the harness straps over the side of the
shell (C), position your child in the child car
32
seat (D) ensuring no toys or other hard objects
are in the seat.
Match the two halves of the harness buck-
les together and insert them into the crotch
buckle (E).
Make sure the shoulder straps fit your child
snugly by pulling the adjuster belt(F).
5
ADJUNTING THE HARNESS HEIGT
Attention: You should not attempt to adjust
the harness height with a child in the child
car seat.
1 The harness strap slots should be level with or
above your child's shoulders.
If they are not, then you may need to repo-
sition the harness shoulder straps and adjust
the harness height.
2 Adjust the shell to its most reclined position.
Pull the recline adjuster handle under the
front of the shell and whilst holding it, pull the
shell forwards to its most reclined position.
Press button (A) and pull up on the shoulder
3
straps (not the shoulder pads) to completely
loosen the straps.
Ensure you loosen the shoulder straps com-
pletely as this will aid the harness removal.
IMPORTANT: DO NOT pull the shoulder pads.
4
Remove the installation bar (B) by pulling the
lock (C) up, on the top right hand side of the
shell.
5
Pull and hold the shell forward.
Unhook the straps at the rear of the seat shell
6
by sliding the straps through the slits in the
shoulder pads connector (D) and yoke( E).
NOTE: The thinner straps are the shoulder
pad straps, and they connect to the shoulder
pads connector (D) and the wider straps are
the shoulder harness straps, and they connect
to yoke (E).
Adjust one side at a time. Pull one set of the
7
shoulder straps through their slot (F) and
avoid twisting the straps.
Pass both the wider straps (H) and narrow
strap (I) back though the shell at your desired
slot height (G), making sure the wider straps
(H) is threaded through the shoulder pad (J),
and that you keep the thinner strap (I) below
the wider strap (H).
Repeat on the opposite side.
8
Check none of the straps are twisted and
reconnect the shoulder pad straps to the
shoulder pad connector (D) and the shoulder
harness straps to the yoke (E).
Return the shell to its original position and re-
insert the installation bar (M) and secure lock
(N).
6