Customer Assistance - Honeywell PLS750C Mode D'emploi

Masquer les pouces

Table des Matières

Les langues disponibles

5.3

Configuration Menu

(Conf)

Use the Configuration menu to set the following parameters (see

sections 5.3.1 to 5.3.4).

5.3.1 Backlight mode (SCRN)

The screen is lit at high intensity for 8 seconds when you press any

button. The rest of the time, depending on the backlight mode

selected, the screen behaves as follows:

Scrn Off: The screen is not lit.

Scrn On HI: The screen is lit at high intensity.

Scrn On LO: The screen is lit at low intensity (default mode).

5.3.2 Automatic Daylight Savings Time Changeover (DLS)

When automatic daylight savings time changeover is on (DLS On), the

PLS750C/PLS751C changes to daylight savings time (summer time)

at 2:00 am on the second Sunday of March and changes back to

normal time (winter time) at 2:00 am on the first Sunday of November.

This function is enabled (DLS On) by default.

5.3.3 Latitude and Longitude Coordinates (LAT and LONG)

The coordinates are used to turn the lights on at sunset and off at sun-

rise. The latitude is set to +45 and longitude to -75 by default. These

settings provide approximate sunset and sunrise times for most North

American cities. To obtain your city's coordinates (or those of a nearby

city), see the coordinates table. You can also obtain this information at

www.geonames.org or with a Global Positioning System (GPS)

device. The accuracy of the sunset and sunrise times depends on the

accuracy of the coordinates you enter for your city.

NOTE: Enter a negative value for a south latitude or a west longitude.

5.3.4 Correction Factor (ADJ)

If your city's time zone is based on political or economic boundaries

instead of its coordinates, your lights might switch on or off too early or

too late with respect to sunrise and sunset. In this case, apply a

correction factor (+1 or -1 hour; refer to addendum). Otherwise, leave

it at 0 (default value).

5.4

Program Menu

(Prog)

Use the Program menu to set the programs; i.e. the times you want

the lights to turn On or Off when the switch is in Automatic mode. To

set a program, proceed as follows:



Select a program number (see section 5.4.1)



Set the day(s) of the program (see section 5.4.2)



Set the program start time (see section 5.4.3)

5.4.1 Selecting a program number

You can set up to 21 "On" programs

("P01 On" to "P21 On") and 21 "Off"

programs ("P01 Off" to "P21 Off"). For

example, select an "On" program to set

when to turn the lights on; select an

"Off" program to set when to turn the

lights off.

5.4.2 Setting the day(s) of the program

After selecting a program, set the day(s) of the program. You can

select a specific day, all 7 days or "none". Choose "none" for any

unused program.

5.4.3 Setting the program start time

After setting the day(s) of the program, set its start time. You can

select either a specific time, the sunset time or the sunrise time:

•

To select a specific time:

(1) Advance to the hour setting and select the hour.

(2) Advance to the minutes setting and select the minutes.

•

To select sunset or sunrise time:

(1) Advance to the hour setting and select the sunset time or

sunrise time. (When you scroll, the sunset time

sunrise time

appear between 11 pm and 12 am.)

(2) To enter an offset (from -70 to +70 minutes in 10-minute

increments) between the sunset or sunrise time and the

program start time, advance to the minutes setting and change

the minutes.

•

EXAMPLE: If the sunset time is 6:13 pm and you change the

minutes to display 6:43 pm, you have entered a delay of 30

PLS750C/PLS751C

minutes. If, later in the year, the sunset time is 4:01 pm, the

program will start at 4:31 pm.

•

NOTE: When you enter an offset,

remove the offset, display the sunset or sunrise time and

change the minutes until

5.4.4 Examples

Example 1: The lights turn on at sunset and off at 11:00 pm every day

(default setting).

Program

P01 On

P02 On to

P07 On

Example 2: The lights turn on at sunset and off at sunrise every day.

Program

P01 On

P02 On to

P07 On

Example 3: The lights turn on at 8:00 pm every day and turn off at

10:00 pm every day except on Saturday night when they turn off at

1:00 am.

Program

P01 On

All 7 days

P02 On

None

P03 On

None

P04 On

None

P05 On

None

P06 On

None

P07 On

None

For example, if you set "P01 Off" at 10:00 pm for all 7 days and set

"P02 Off" to 11:00 pm for Saturday, on Saturday, the lights will turn off

at 10:00 pm, not 11:00 pm since "P01 Off" is set to an earlier time than

"P02 Off".



Keypad Lock

When the keypad is locked, the

only change permitted is the changing of the state. For example, if the

lights are off, they will turn on when you press the main button.

However, in Automatic mode, the default state for the current program

will be overridden until the next program starts. If you press the main

button again before the start of the next program, the lights return to

their initial state. To lock or unlock the keypad, press the buttons

in the following order:

"P01 On"

"P01 Off"

NOTE: You must perform the whole procedure in an interval of 2

seconds. If the procedure was not properly performed, wait another 2

seconds before retrying.



Reset to default Settings

return

simultaneously press both main and left buttons and

hold. The software version will appear for 5 seconds.

RST will appear for the next 5 seconds. Release the

buttons when all segments appear on the screen. The

and

switch is now reset (see default settings in the menu

flowchart).

appears along with

when you display the sunset or sunrise time. To

disappears.

Days

Time

Program

Days

All 7

sunset

P01 Off

All 7

days

None

—

P02 Off to

None

P07 Off

Days

Time

Program

Days

All 7

sunset

P01 Off

All 7

days

None

—

P02 Off to

None

P07 Off

Days

Time

Program

Days

8:00 pm

P01 Off

Sunday (Su)

—

P02 Off

Monday (Mo)

—

P03 Off

Tuesday (Tu)

—

P04 Off

Wednesday (We)

—

P05 Off

Thursday (Th)

—

P06 Off

Friday (Fr)

—

P07 Off

Sunday (Su)

Be careful about overlapping!

icon appears on the screen and the

2 sec.

the

switch

its

default

settings,



Troubleshooting

The display is faded or

The ambient temperature is either below

irregular.

or above switch's operating temperature.

The display disappears

Swap the LINE and 3-WAY wires.

when you toggle the

other switch.

The sunset or sunrise

• The date or time is wrong

time is inaccurate.

Time

• The longitude or latitude is wrong

11:00

• The correction factor is wrong

—

• You have entered an offset



Specifications

Time

sunrise

Supply: 120 VAC, 60 Hz

—

Maximum

load: 1800 watts

Operating temperature

range: -15 °C to 50 °C (5 °F to 122 °F)

Storage temperature

range: -40 °C to 60 °C (-40 °F to 140 °F)

Power

outage: The screen is blank. Only the time must be set if the

outage lasts more than 4 hours; all other settings and programs are

permanently saved.

Time

Latitude

range: from -65° to +65°

10:00 pm

Solar table

precision: +/- 11 min. (within ±60° latitude)

10:00 pm

Certification: UL (c UL us)

10:00 pm



10:00 pm

Warranty

10:00 pm

Honeywell warrants this product, excluding battery, to be free from defects

1:00 am

in the workmanship or materials, under normal use and service, for a period

of three (3) years from the date of purchase by the consumer. If at any time

during the warranty period the product is determined to be defective or mal-

functions, Honeywell shall repair or replace it (at Honeywell's option).

If the product is defective,

(i)

return it, with a bill of sale or other dated proof of purchase, to the

place from which you purchased it, or

(ii)

call Honeywell Customer Care at 1-800-468-1502. Customer Care

will make the determination whether the product should be returned

to the following address: Honeywell Return Goods, Dock 4 MN10-

3860, 1885 Douglas Dr N, Golden Valley, MN 55422, or whether a

replacement product can be sent to you.

This warranty does not cover removal or reinstallation costs. This warranty

shall not apply if it is shown by Honeywell that the defect or malfunction was

caused by damage which occurred while the product was in the possession

of a consumer.

Honeywell's sole responsibility shall be to repair or replace the product

within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR

ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL

OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDI-

RECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR

IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states do

not allow the exclusion or limitation of incidental or consequential damages,

so this limitation may not apply to you.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL

MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WAR-

RANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE

THREE-YEAR DURATION OF THIS WARRANTY. Some states do not

allow limitations on how long an implied warranty lasts, so the above limita-

tion may not apply to you.

This warranty gives you specific legal rights, and you may have other rights

which vary from state to state.

If you have any questions concerning this warranty, please write Honeywell

Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call

1-800-468-1502.

