Cleaning And Maintenance - Oregon PN Q515061 Notice D'utilisation

CAUTION
This face shield does not provide unlimited face protection. For your own protection read these instructions completely before using this face protection.
REQUIREMENTS
This face shield complies with the requirements of the European Regulation (EU)2016/425 by means of the European Standards
EN166: 2001/ EN1731: 2006 «Personal Eye Protectors-Specification»
STORAGE
When not in use, it is recommended to store the face shield in a clean and dry polybag or case for visor protection.
DIRECTION FOR USE
This face shield has been designed for your personal safety. It must be worn for the whole duration of exposure to hazards, leave the work area if dizziness or
irritation occurs, or if the face shield becomes damaged.

CLEANING AND MAINTENANCE

To maintain your face shield in good condition:
1. Do not use abrasive materials, clean and rinse in warm soapy water and dry with a soft cloth.
2. Any part of face-protector which is in contact with the wearer shall be disinfected by alcohol.
FIELD OF USE
This face shield is designed to protect the user against eye and face injuries through mechanical impact or splashes of liquids (Except 566093 visor). The face
shield is marked on the brow protection and visor with a series of numbers and symbols to indicate the manufacturer, the field of use, the protection capabilities
and performance characteristics of the face-protector. Appropriate markings on ocular and frame are signified as follows:
MARKING OF THE OCULAR
CE CE Certification
S Symbol of protection against increased robustness at a speed 5.1 m/s
F Symbol of protection against high speed particle, low energy (45m/s)
B Symbol of protection against high-speed particle, medium energy (120m/s)
1 Optical Glass
OREGON Identification of the manufacturer
MARKING OF THE FRAME
CE CE Certification
S Symbol of protection against increased robustness at a speed 5.1 m/s
F Symbol of protection against high speed particle, low energy (45m/s)
B Symbol of protection against high-speed particle, medium energy (120m/s)
3 Symbol of protection against droplets and splashes of liquid
EN 1731 Number of the standard, which the product fulfils
EN 166 Number of the standard which the product fulfils
OREGON Identification of the manufacturer
REPLACEMENT OF SPARE PARTS, ACCESSORIES AND INSTRUCTIONS FOR FITTING
Only use original spare parts. To replace the visor, you should ensure the compatibility of marking and the right visor is fitted.
DURATION OF USE
Inspect for damage regularly. When the face-protector has become brittle the face shield should be replaced.
If parts of protector or protector itself must be replaced, please use recycled material which written on product.
If stored and used correctly, is over 3 years.
However, we would recommend it be changed every 2-3 years as necessary.
PACKAGING SUITABLE FOR TRANSPORT
It is recommended to put face shield (including brow-guard and visors) in their original packaging which consist in a poly-bag or box or blister to avoid exposing
to air and dust.
WARNING
• This product is for face protection against moderate impact hazards but NOT unbreakable
• Do not modify or alter the face protector
• Pitted or scratched screen reduces vision and seriously reduces protection and should be immediately replaced.
• This face protector has not any filtering action. It does not protect against molten metal splash, hot solids or electrical hazard. Mesh visor (566093) does not
protect also to liquid projection and UV and IR light.
• Always check with supervisory personnel to ensure you are being given the proper protection relative to working conditions, consult relative European stan-
dards.
• The material which may come into contact with the wearer's skin could cause an allergic reaction to susceptible individuals.
• If the symbols S,F,B, and A are not common to both ocular and the frame then it is the lower level which shall be assigned to the complete eye-protector.
• The protectors against high speed particles launched on ophthalmic spectacles can cause shock, causing a hazard to the user.
609732 + 609731/566093
CE Test
609729 + 609731/566093
BSI Group
CE Approval Notify Body No.0086
Kitemark Court, Davy Avenue, Milton Keynes, MK5 8PP , United Kingdom
BLOUNT EUROPE SA
Manufacturer
RUE EMILE FRANCQUI 5, B-1435 MONT-SAINT-GUIBERT, BELGIUM
EU
Declaration of Conformity is available at http://www.oregonproducts.eu/doc/
2
1903 Face Shield Instructions manual_Q515061-Q515062-Q515063-Q515064.indd 2
EN
CRITT Sport Loisirs
Notified body NO.0501
ZA du Sanital, 21 rue Albert EINSTEIN 86100 Chatellerault, France
16/04/19 15:38