Lighting Instructions; Shutdown Instructions; Important - Mr. Heater MH4GC Instructions D'utilisation Et Manuel Du Propriétaire

NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING! NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!

Lighting Instructions

ALWAYS ATTACH OR DETACH
CYLINDER OUTDOORS AWAY FROM
FLAMES, OTHER IGNITION SOURCES,
AND ONLY WHEN HEATER IS COOL
TO TOUCH. NEVER SMOKE WHEN
ATTACHING OR REMOVING PROPANE
CYLINDER!
• LP cylinders must be marked in
accordance with "Cylinders, Spheres
and Tubes for Transporation of
Dangerous Goods, CAN/CSA B339".
• Use only LP-gas cylinders marked in
accordance with the U.S. Dept. of
Transportation (DOT).
• Use only 16.4 oz. (1 lb.) disposable
cylinders that mate with No. 600 valve
connection.
• Heater and attached cylinder must
be in an upright position during
operation.
1. Screw 1 lb. disposable LP-gas supply
cylinder clockwise (from bottom) into
portable heater until hand-tight and fit
cylinder into stand. Do not use thread
sealant on this connection. Be sure
cup adapter fits tightly into cup holder
before moving.
2. Check cylinder connection for leaks
with soapy water at the threaded
connection under the domed plastic
cover where the cylinder screws into
the regulator. SEE WARNING! ON
PLASTIC COVER.
3. Depress "ON" button to light pilot
flame (repeat until pilot lights) and
continue to hold for 30-60 seconds.
4. After lighting pilot, release "ON"
button to light heater. The white tile
will take a few moments to start to
glow.

Shutdown Instructions

1. To shut off heater, press the "OFF"
button.
• Do not operate, store or remove
cylinder near flammable items or
ignition sources.
• LP-GAS CYLINDERS MUST BE
DISCONNECTED FROM HEATER WHEN
NOT IN USE!
Maintenance
• Always keep the heater area clear
and free from combustible materials,
gasoline and other flammable vapors
and liquids.
• Keep the vent areas (slots in the
bottom and top of the heater) clear at
all times.
Mr. Heater | Portable Radiant Golf Cart Heater
• Visually inspect the pilot flame and
burner periodically during use. The
pilot flame should be blue in color
(not yellow) and will extend to the
thermocouple. The flame will surround
the thermocouple just below the tip,
see Figure 1.
• A slight yellow flame may occur where
the pilot flame and main burner
flame meet. The burner should be
bright orange (with a slight blue color
around the border, a red-orange haze
that is visible on the ceramic tile is
acceptable) and without a noticeable
flame.
• A blue flame that rolls out at the
top of the ceramic tile indicates an
accumulation of dust, lint or spider
webs inside the housing assembly and
main burner assembly. If the pilot is
yellow or the burner has a noticeable
flame, cleaning may be required. Use
the following procedure to inspect
the casing assembly and main burner
assembly. It is necessary to periodically
check the burner orifice and burner
venturi to make sure that they are
clear of things such as insect nests
and spider webs that may accumulate
over time. A clogged tube can lead to
a fire.
Cleaning Instructions (Refer to
Exploded Parts on Page 6):
IMPOR TANT: Allow heater to
thoroughly cool before performing any
maintenance.
1. Remove disposable 1 lb. propane
cylinder from heater.
2. Remove right side plastic service panel
(ref.4) by removing the six screws
holding it in place.
3. Inspect the interior of casing for
accumulation of dust, lint or spider
webs. If necessary, clean the interior
of the casing assembly with a vacuum
cleaner or compressed air (max 30
psi). Do not damage any components
within the casing assembly when you
are cleaning.
4. Inspect and clean main burner (ref. 3)
and orifice (ref. 8) by using a vacuum
or compressed air (max 30 psi).
5. Inspect and clean pilot tube (ref. 7).
Insert a doubled over pipe cleaner
into the pilot tube until it bottoms
against the pilot orifice (approximately
4
Operating Instructions and Owner's Manual
Pilot Flame
Oxygen Depletion
Sensor
Figure 1
WARNING: Always inspect propane
cylinder and heater propane connections
for damage, dirt, and debris before
attaching propane cylinder. Do not use if
head of cylinder is damaged, punctured
or deteriorated.
WARNING: Heater must not be
exposed to flammable vapors or liquids
during ignition or operation.
CAUTION: After turning heater off,
wire guard will remain hot. Allow to
thoroughly cool before storing.
WARNING: Never use needles, wires
or similar cylindrical objects to clean the
pilot to avoid damaging the calibrated
ruby that controls the gas flow through
the pilot orifice.
2"). Rotate the pipe cleaner a couple
of times and remove. Blow out the
remaining debris using compressed air.
6. Apply compressed air (max 30 psi) into
the ceramic tile of burner assembly
and venturi tube (ref. 3) to remove
dust, lint and spider webs.
7. Reinstall the right side plastic service
panel.