Book Marking - Arcam FMJ DV27A Mode D'emploi

A number of aids have been built in to the programme menu to make
it easier to use.These are best illustrated by an example. Let's assume
that you want to play chapters 5, 7, 9, 4, 8, 3, and 1 (in that order) of
title 1, then all of title 2.
1: 1 5 6: 1 3
2: 1 7 7: 1 1
3: 1 9 8: 2 All
4: 1 4 9: – –
5: 1 8 10: – –
2 Title(s) on this disc.
27 Chapter(s) in this title.
Enter title number.
First, highlight the title position for the first programmed item (as
shown in the screen above).Then press the number
control:'1' is shown in the position. Using the remote control, press to
highlight the chapter position.The message at the bottom of the screen
changes accordingly, prompting you for the required information. Press
on the remote handset.
5
Since we have a number of chapters all from the same title, it would
be a lot of work to have to enter the title number each time. Press
on the remote handset. Notice that the player assumes that the title
number remains the same for this entry as for the previous one. Enter
the remaining chapter numbers, pressing
pressing at the bottom of a column places the cursor at the top of
the next column.)
Next, we want to specify all of title 2. For this, highlight the title position
of the next entry (entry 8) and enter the number
Highlight the chapter position and, without entering any number, press
.The player fills in the text 'All' to indicate that all the chapters in title
2 will be played.
PROGRAM (DVD-AUDIO)
The programming of a sequence for a DVD-audio disc is essentially the
same as for a DVD-video disc, and the instructions given above should
be followed. For DVD-audio discs, the"titles with chapters" combination
found on DVD-video discs changes to "groups with tracks".
PROGRAM (VCD)
The bottom of the screen shows the number of tracks present on the
disc. Below this is an information line, giving relevant information for the
cursor position.
You can enter a sequence of up to 20 tracks for programmed playback.
If you enter data that is invalid for the current disc, the field is erased
automatically.
To program the player, highlight the first entry (using the cursor pad on
the remote control), then press the number of the track you want to
play first. To enter a second track, move down, then type the number
of the second track to play, etc. To enter a track number greater than
9, press the two digits sequentially (e.g., for track 10, first press
press ).
0
To play the programme you have entered, highlight the
the screen and press .The 'PROG' indicator shows on the front panel
OK
display and the programmed sequence begins.
If you make a mistake while programming, you can clear a single field by
highlighting it and pressing
CLEAR
the 'CLEAR ALL' button on the screen and press
To stop the programmed sequence and return to normal playback,
select the 'PLAY' button in the programme menu with no programme
specified. This clears programme mode and causes normal playback
order to be resumed.
Play Clear All
11: – – 16: – –
12: – – 17: – –
13: – – 18: – –
14: – – 19: – –
15: – – 20: – –
on the remote
1
after each one. (Note that
, indicating title 2.
2
1
button on
PLAY
.To clear all the fields at once, highlight
.
OK
GENERAL
To play the programme you have entered, highlight the 'PLAY' button
on the screen and press
and the programmed sequence begins.
If you make a mistake while programming, you can clear a single field by
highlighting it and pressing
the 'CLEAR ALL' button on the screen and press
To stop the programmed sequence and return to normal playback,
select the button in the programme menu, with no programme
PLAY
specified.This clears the programme mode and causes normal playback
order to be resumed.
Note that skipping forward or back through tracks while in programmed
play mode skips through the programmed sequence.

'BOOK MARKING'

It is possible to 'bookmark' up to three points on a DVD title, allowing
you to jump directly to those parts of the disc in the future.
STORING A BOOKMARK
1. Start playback of the disc from a point about 30 seconds before
the point that you would like to bookmark.
2. Press the
MEM
the bookmark menu.
3. Three bookmark locations will be displayed. Highlight one of the
locations using the cursor pad on the remote control. It does not
matter to the player which location you use.
4. At the point of the disc you wish to bookmark, press the
button.The menu will close automatically.
PLAYING FROM A BOOKMARK
1. Insert the disc into the machine that you would like to play. Once
playback of the disc has started, press the
2. Any bookmarks set for this disc will be shown on the display
(indicated by the time of the bookmark). Note that the time of
each bookmark is relative to the start of the title that contains
the bookmark, not to the start of the disc.
3. Highlight the bookmark that you wish to activate, then press
.
OK
4. The bookmark menu will close automatically, and playback will
start from the location of the bookmark.
CLEARING A BOOKMARK
Bookmarks for a particular disc may be cleared only if the disc is in the
player.
1. With the disc in the player, press the
2. Any bookmarks set for this disc will be shown on the display.
3. Highlight the bookmark that you wish to clear, then press
, then
.
CLEAR
4. Press to close the bookmark menu.
MEM
Bookmarks may be stored for up to 50 discs, with each disc having up
to three bookmarks.
17
.The 'PROG' indicator shows in the display
OK
.To clear all the fields at once, highlight
CLEAR
.
OK
button on the remote control.This will open up
button.
MEM
button.
MEM
OK