Code Search; Code Identification - Schwaiger UFB 801 Mode D'emploi

Schwaiger UR 8 is a TV+ remote control, i.e. under TV you can
only set television sets or video projectors. But you can
dedicate any appliance (TV, DVD, SAT...) to the VCR, DVD,
SAT, CD, AUX, AUX1, AUX2 keys. The button labels SAT,
DVD,VCR, etc. are intended only for easier orientation.
Example: Under the VCR appliance button you can also enter
a CD code and control your CD player. You just need to find
your appliance brand in the CD section of the code book. Just
enter the first 3 digit code under the VCR key (refer to 3.1.1).

3.2 CODE SEARCH

If the brand of your appliance is not listed or none of the codes
given fits, we recommend a code search.
As you can dedicate any appliance (TV, DVD, SAT...) to the
VCR, DVD, SAT, CD, AUX, AUX1, AUX2 keys, you need first to
enter any 3 digit code for the kind of appliance you wish to
control (found in the code book), i.e.: If you want to program a
SAT under the VCR key, enter any SAT code corresponding to
your appliance brand, available in the code book (refer to 3.1.1)
and then follow the steps below:
3.2.1 Slow code search
3.2.1.1 Switch on the appliance to be controlled.
3.2.1.2 Keep the SETUP button pressed until the lamp
lights constantly.
3.2.1.3 Press the required appliance button, e.g.
3.2.1.4 Press the ON/OFF
CHAN+ (next channel) button repeatedly until the appliance,
e.g. your DVD player, reacts. With video recorders, etc. you can
also press the PLAY button repeatedly. If you want to search
with PLAY, place a cassette or disk in your appliance before
searching.
Each time a button is pressed the lamp goes out briefly then
comes back on to confirm.
If no button is pressed, the UR 8 automatically continues to
search by sending a signal to your appliance every 3 seconds.
If you notice the reaction of your appliance too late and the next
code has already been emitted you can go back by pressing
CHAN-. If your appliance was switched off, you must turn it on
again, pressing its own "power" button, or with its original
remote control, to continue the search.
3.2.2 When your appliance reacts, simply press
to confirm the code and stop the search.
3.2.3 To test whether the right setting has been found, simply
press a few buttons on the UR 8 and check whether the
functions work correctly. If everything is OK you can now set the
UR 8 for the second appliance.
If nothing happens or some of the buttons do not work correctly
you must let the UR 8 continue to search for the correct setting
as described starting in 3.2.1.
The UR 8 continues the search at the point you stopped It with
the button. When the end of the code list is reached the
search stops automatically. The remote control blinks quickly
several times. The code last confirmed with
stored.
3.2.4 Searching by brand
You can considerably speed up the code search if you search
by brand. This is done as follows:
3.2.4.1 Switch on the appliance to be controlled. Program is
running.
3.2.4.2 Keep the SETUP button pressed until the lamp
lights constantly.
3.2.4.3 Press the required appliance button, e.g.
3.2.4.4 Press the brand number button, button 1 for Philips, 2
for Sony, 3 for Thomson, 4 for Grundig or 6 for Nokia
appliances. Then continue as described in 3.2.1.4.
The remote control will send all the TV codes of the brand you
have selected. This search by brand is not suitable if you wish
to dedicate a key to another appliance, e.g. VCR key to a DVD.
Christian Schwaiger GmbH & Co. KG, Würzburger Str. 17, 90579 Langenzenn
3.3 QUICK CODE SEARCH
Your remote control finds the correct settings almost
automatically in seconds:
3.3.1 Switch on the appliance to be controlled with its own
power button.
3.3.2 Keep the
constantly.
3.3.3 Press the required appliance button, e.g.
3.3.4 Press the ON/OFF
briefly.
3.3.5 Automatic quick search: the UR 8 automatically sends a
different IR code each second. When your appliance reacts,
immediately press the
– We advice you to place your finger over the
button so that you can react quickly enough. Otherwise the UR
8 transmits the next signal before you have reacted.
Note: With very few appliances the quick search does not work.
The search is automatically stopped if there is no reaction from
the appliance to be controlled. You should then use a different
setting procedure, e.g. code entry or slow search.
Instead of pressing
DVD.
correct code you can also switch the UR 8 to slow code
search: to do so, press the CHAN+ or ON/OFF button instead
(appliance on/off) or
of the
in 3.2.1.
Remember to switch on your appliance again, e.g. DVD, if you
wish to continue the search.
3.3.6 Finally, test the set code by controlling e.g. your DVD
appliance. If it does not work correctly, please start the code
search again. The code search then starts with the next code in
the sequence.

3.4 CODE IDENTIFICATION

You can identify the codes found at any time:
3.4.1 Keep the
remains lighted.
ENTER
3.4.2 Press the appliance button, e.g.
3.4.3 Press the
3.4.4 Then read off the 3-digit code: To identify the first digit
press each number button from 0 – 9 (9) until the LED blinks.
The number you pressed is the first digit of the code.
Press each number key from 0 – 9 as above to find the second
digit.
Press each number key from 0 – 9 as above to find the third
digit. When the third digit has been found the LED will go off.
Don't forget to write down the code on the label of the battery
compartment.
Example: You want to read off the code under the TV button.
To do so, keep SETUP pressed until the lamp lights constantly.
remains
Then press TV, SETUP, 1 in succession. For button 1 the light
goes out briefly and you note 1. Then continue by pressing
1,2,3,4,5. For button 5 the light goes out briefly and you write 5
after 1. Then continue by pressing 1,2. For button 2 the light
goes out completely and you note the 2. After 15 and have
found the code 152.
3.4.5 You can note the numbers on the back of the battery
compartment door, e.g. for quick code entry after replacing the
batteries.
The code details are also required when making queries on the
Schwaiger Hotline. Please read off all the codes used and
TV.
make a note of them before contacting the Hotline. Table: see
the end of these instructions.
Once the code is known, the Hotline can explain which buttons
you can use with the code concerned.
4 OPERATION
You operate the basic functions of your appliances in the same
way as if you were using the original remote controls.
4.1 Select appliance: You select the appliance to be controlled
using the appliance buttons TV, VCR etc., row (B) (see
,
Internet www.schwaiger.de e-mail info@schwaiger.de
SETUP button pressed until the lamp lights
(appliance on/off) button once
button (Enter) to confirm the code.
(Enter) and eventually missing the
(Enter) button. Then continue as described above
SETUP button pressed until the lamp
DVD.
SETUP button once briefly.
DVD.
(Enter)