Profile Design HSF Aeria Instructions D'installation

Note to Dealers: If you install this product for the consumer, please provide him/her with this owner's manual after
installation.
Thank you for purchasing the HSF Aeria. Please read these instructions thoroughly before attempting to install this
accessory. Proper installation is required for compliance with the Profile Design warranty policy. If you need help with this
installation, please seek the assistance of your local Profile Design dealer by logging on to www.profile-design.com and
using "dealer search" or by calling the Profile Design customer service number.
The included bracket is compatible with the Profile Design Aeria Ultimate Stem. It will not fit on standard stems with front
address face clamps.
Installing the HSF Aeria
For first time installation of a pre-assembled HSF Aeria
1. Affix the bracket to the underside of the Aeria Ultimate stem using the supplied M5x 16mm & M5x 14mm bolts.
Tighten to 2Nm/20kgf-cm The curve of the bracket should sit snugly against the curvature of the stem base, with the
lower rail horizontal.
2. Attach the rubber shroud to the back of the bottle by pressing against the sides of the shroud to expand the retention
groove. Allow this to close around the matching T-rail on the back of the of the bottle
3. Slide the bottle on to the bracket, first ensuring that the socket is lined up with the mounting rail. Push firmly until you
hear the retention clip click into place. Verify that the bottle is securely attached by attempting to pull it off (without first
disengaging the clip)
4. To remove the bottle press the back of the retention clip beneath the stem, this will allow the bottle to slide forward
5. Examine the fit between the shroud and the frame, if the shroud is pressed against the frame you may wish to carefully
make a vertical cut to reduce the interference. We suggest using a sharp cutting tool with appropriate caution to
remove material in steps. Please remove the bottle/shroud first to avoid the risk of damaging your frame and brake/
shift cables
Please note that the HSF Aeria is only compatible with the Profile Design Aeria Ultimate stem. It cannot be fitted to
any other Profile Design stem or the products of any other manufacturer.
Assembling the HSF Aeria
If your HSF Aeria system has been disassembled, take the following steps to prepare it for installation:
1. Fit the fill port gasket and straw o-ring to the bottle. We suggest you ensure your hands are clean before touching any
of the bottle parts that come into contact with your hydration
2. Affix the cover to the bottle, push firmly until the clips latch on both sides
3. If you wish to mount a computer, attach the computer mount to the nose. Torque the M5x 18mm bolt to 2Nm/20kgf-cm.
4. If you do not intend to fit a computer, attach the nose cover. Torque the M5x 18mm bolt as same level as front cap.
5. Install the straw carefully to ensure the o-ring is not pushed out or twisted
6. Slide the magnet on to the straw, setting it at a distance that allows a good connection with the magnet in the cover
7. If you are using risers and a bridge on the Profile Design Aeria Ultimate bars, you can choose to affix the satellite
magnet mount to the bridge to allow simpler hose management
WARNING
• Any failure to follow these warnings and instructions can result in breakage, slippage and or other malfunctioning of this Profile Design component causing a loss of control of the bicycle with serious injuries. [AP1100-1-1]
• Whenever you install any new component on your bike make sure you thoroughly try it out close to home (with your helmet) where there are no obstacles or traffic. Make sure everything is working properly before going off on a ride or to a
race. [AP1100-5-1]
• Racing (road, mountain or multi-sport) places extreme stress on bicycles and their components (like it does riders) and significantly shortens their usable life. If you participate in these types of events, the lifetime of the product may be
significantly shortened depending upon the level and amount of racing. The "normal wear" of a component may differ greatly between competitive and non-competitive uses, which is why professional level riders often use new bikes and
components each season as well as having their bikes serviced by professional mechanics. Particular care should be placed in the regular examination of your bicycle and it's components to insure your safety. [AP1100-6-1]
• Aerobars can require riding positions that are new or different to many riders. It is advisable to practice using these bars in a low traffic area to become accustomed to any changes in the steering or handling characteristics of the bike.
Please exercise caution when using these types of handlebars for the first time. Also make sure that you continue to look forward when riding and do not look down towards the ground. [AB1100-2-1]
Profile Design, LLC
Worldwide Limited Warranty
Profile Design LLC warrants to the original retail purchaser ("you") that the Profile Design product for which they
received this warranty is free from defects in material and workmanship for two years from the date of original retail
purchase. This warranty is not transferable to a subsequent purchaser. Profile Design's sole obligation under this
warranty is to repair or replace the product, at Profile Design's option. Profile Design must be notified in writing of
any claim under this warranty within 60 days of any claimed lack of conformity of the product.
Warranty Limitations
The duration of any implied warranty or condition, of merchantability, fitness for a particular purpose, or otherwise, on
this product shall be limited to the duration of the express warranty set forth above. In no event shall Profile Design
be liable for any loss, inconvenience or damage, whether direct, incidental, consequential or otherwise, resulting
from breach of any express or implied warranty or condition, of merchantability, fitness for a particular purpose,
or otherwise with respect to this product, except as set forth herein. Some states or countries do not allow
limitation on how long an implied warranty lasts and some do not allow exclusions or limitations of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you
specific legal rights, and you may also have other rights, which may vary, from location to location. This warranty
will be interpreted pursuant to the laws of the United States. The original English language version/meaning of
this warranty controls over all translations and Profile Design is not responsible for any errors in translation of this
warranty or any product instructions. This warranty is not intended to confer any additional legal, jurisdictional or
warranty rights to you other that those set forth herein or required by law. If any portion of this warranty is held
to be invalid or unenforceable for any reason, such finding will not invalidate any other provision. For products
purchased in countries other than the United States please contact Profile Design's authorized distributor in that
respective country.
Warranty Service Options
To obtain service under this warranty you must either:
(1) Bring or send your Profile Design product, together with this warranty, the retail seller's original receipt or other
satisfactory proof of the date of purchase to the retailer where you purchased the item or another authorized
Profile Design retailer, or
(2) Send your Profile Design product (with the return authorization number on the outside of the shipping container
and affixed to the product), together with the retail seller's original receipt or other satisfactory proof of the
date of purchase to Profile Design 2677 El Presidio St., Long Beach, CA 90810 USA. You must first obtain a
return authorization number by calling Profile Design at (310) 884-7756 ext. 161 (or send an email to warranty@
profile-design.com) prior to returning the product to Profile Design.
Profile Design may require that you complete and sign a warranty replacement request form before processing
your warranty claim.
Profile Design HSF Aeria
3
2
5
Ref.# Part #
1 B057
2 B115
3 B116
4 313591
5 B117
6 B118
7 B119
8 B140
9 313589
10 313590
11 B058
12 B096
13 B137
14 B138
15 B139
Any postage, insurance or other shipping costs incurred in sending your Profile Design product for service under
either option above is your responsibility. Profile Design will not be responsible for products lost or damaged in
shipping.
For products purchased in countries other than the United States please contact Profile Design's authorized distributor
in the country where the product was purchased. They can be found on our website at www.profile-design.com
Profile Design Crash Replacement Policy
Profile Design understands that crashes can happen and replacement of damaged bicycle parts can be costly.
As a result Profile Design will attempt to ease the pain by offering you a replacement product for 30% below
Profile Design's current suggested retail price in your respective country. All other provisions of this warranty
apply and the procedures outlined for warranty service apply also to the crash replacement policy. Profile Design
will make the final decision on whether the part will be covered under the crash replacement policy.
Warranty Exclusions
Retailers and sellers of Profile Design products are not authorized to modify this warranty in any way. It is your
responsibility to regularly examine the product to determine the need for normal service or replacement. This
warranty does not cover the following:
• Products that have been modified, neglected or poorly maintained, used for commercial purposes, misused or
abused or involved in accidents.
• Damage occurring during shipment of the products (such claims must be presented directly to the shipper).
• Damage to products resulting from improper assembly or repair, the use or installation of parts or accessories not
compatible with the original intended use of the product, or the failure to follow the product warnings and usage
instructions.
• Damage or deterioration to the surface finish, aesthetics or appearance of the product.
• The labor required to remove and/or re-fit and re-adjust the item covered by this warranty.
• Normal wear to the product.
• Any products for which the consumer does not follow the warranty procedures outlined above.
For the current version of this warranty please visit our website at www.profile-design.com
(© June 2006 Profile Design)
01.01.IA00952 Profile Design HSF Aeria 04/08/2019
Installation Instructions
14
15
4
6
13
1
10
7
12
11
Qty. Req. Part Description
2 Cap - Anti-Splatter
1 Front Cap - Computer Mount - Aeria HSF
1 Front Cap - Rubber Cover - Aeria HSF
1 Bolt M5 x 18 FHB
1 O-Ring - Straw Stabilization
1 Rubber - Movable Magnet - Aeria HSF
1 Rubber - Head Tube Filling - Aeria HSF
1 Bottle - Aeria HSF Black (Integration)
1 Bolt M5 x 12 FHB
1 Bolt M5 x 16 FHB
1 Straw - 360mm
1 Bite Valve Gray
1 Cap - Top of Bottle - Aeria HSF (Integration)
1 Magnet System - Straw - Aeria HSF (Integration)
1 Magnet System - Movable - Aeria HSF (Integration)
www.profile-design.com
9