Installation; Use - Sidi MiniVapor Installation, Utilisation Et Entretien

 If you have to refill the boiler again, please be careful
and keep away from the boiler, because drops of water
in contact with the warm boiler can still evaporate and
spray steam.
 DO NOT TURN THE APPLICANCE UPSIDE-DOWN to
drain the boiler. To drain, tilt it from the side of the
safety cap to avoid possible limescale residue blocking
the solenoid valve.

INSTALLATION

Before any operation, please read carefully the
"Warnings".
UNPACKING AND LOCATION
Carry out the following procedure:
a)
Take the appliance and accessories out of the box.
b)
Place the appliance as indicated in "Safety warnings-
Site".
c)
Assemble the accessories provided (see "Installation -
Accessories").
ACCESSORIES
Use the provided accessories as follows:

Insert the cable support 10 in one of the holes 9,
according to the preferred use, left or right hand
operation.

Place the steam tube and the electrical cable 14
between the boiler and the iron in its support on the
support cables 10.

Use the funnel 19 to fill the boiler.

Use the water level gauge 20 to measure the water
inside the boiler 1 (see "Use – Preparation").

Use teflon sole 21 or 22 to help prevent shining when
ironing.
Before using, please read the "Warnings" section
carefully.
PREPARATION
Fill the boiler as follows:
a)
Unscrew the safety cap 2.
b)
Fill the boiler 1 using the provided funnel 19.
c)
Screw the safety cap 2, make sure that it is correctly
closed.
The boiler capacity depends on the model (see
"Technical specifications").
For a faster and ready steam ironing do not fully fill the
boiler (1 litres = 1,5/2h ironing - 1,5 litres = 2/2,5h
ironing).
Measure the water inside the boiler by means the water
level gauge 20 as follows:
a)
Put the water level gauge all the way into the boiler.
b)
Place your thumb to totally cover the open end of the
water level gauge and read the level of the water when
the level gauge is removed from the boiler.
c)
Put the water level gauge 20 back into the boiler and
release your thumb to release the water trapped inside
the water level gauge.
IF whilst ironing the boiler runs out of water, please wait
20/25 minutes before filling it again, useful time to the
boiler for cooling down (see "Warnings – Boiler"), then it
is possible refill the boiler and switch on the appliance
(see "Use – Turning on the appliance").

USE

TURNING ON THE APPLIANCE
Connect the electrical cable to the wall socket and carry
out as follows:
a)
Turn on the boiler switch 5 (only for steam ironing).
b)
Turn on the iron switch 6.
When the appliance has been turned on (see "Use –
Turning on the appliance"), wait until the boiler
temperature is stabilised, the central light for steam is (7)
lit and then is possible to start with ironing with steam.
The central light 7 turns on and off during use of the
appliance. This indicates the boiler maintaining a correct
and constant temperature.
If the central light 7 stays off and no steam is released
from the iron, this indicates that the boiler has run out of
usable water you you must refill the boiler (see "Use –
Preparation").
Turn the steam regulation hand wheel 4 located on the
solenoid valve 3 to control the steam flow volume; use
this control to increase the steam flow by turning it in an
anti-clockwise direction, turning the control in clockwise
direction reduces the steam flow and volume (not
available for 1,8/B and 1,8/P mod.). Make sure that
during the steam ironing it is not completely closed.
A slight smell may occur when first putting the appliance
into operation, this is harmless and stops after a short
time. This is normal and due to the materials of
construction wearing in - it doesn't indicate any damage
to the appliance.
The ironing temperature must conform to the fabric being
ironed, check the manufacturer's label on the garment.
Set the iron temperature by shifting the hand wheel 16,
increase the temperature by turning in clockwise direction
and in anti-clockwise direction to decrease it
Thermostat symbols explanation:
● Nylon
●● Silk
●●● Wool
●●●● Cotton
●●●●● Flax
Carry out as follows:
a)
Set the iron temperature to the required temperature
for the fabric (see "Use – Iron operation").
b)
When the appliance is turned on (see "Use – Turn on
the appliance"), wait for 2-3 minutes until the iron
temperature stabilises.I After this time, it is possible to
start working. DO NOT USE THE STEAM SWITCH 17
as the iron temperature is not suitable for steam and if
operated water may form and limescale will deposit on
the sole of the iron..
Carry out as follows:
a)
Set the iron temperature to the required temperature
for the fabric (see "Use – Iron operation").
b)
When the appliance is turned on (see "Use – Turn on
the appliance"), wait until the steam has built up in the
boiler (litres 1,8 about 15/20 minutes, litres 2,5/4 about
25/30 minutes) until the central light for steam is lit 7
- 11 -
BOILER OPERATION
IRON OPERATION
(only dry ironing)
(only dry ironing)
(dry/steam ironing)
(steam ironing)
(steam ironing)
DRY IRONING
STEAM IRONING