Starting The Machine; Cuttin G Depth Adjustmen T - Virutex SR74K Mode D'emploi

1. SAFETY IN STRUCTION S FOR
HAN DLIN G THE CIRCULAR SAW
• Before use, please read the instructions on use very
carefully, as well as the safety instructions. T hese
instructions will help you to carry out your work in
the best possible way with no risk to yourself, your
workmates or your machine. We recommend that
you keep all the documents relating to your machine
carefully on hand during use, so that you can refer
to them if necessary during your work, and also that
you keep a copy in a safe place, if possible.
• Always inspect cable and plug before using machine.
• Before attempting to work on the machine, unplug
it from the mains.
• Always keep the cable away from the moving parts
of your machine.
• Put the plug into the mains socket only when the
machine is switched off.
• If you need to use an extension cable, the wires
must have a minimum section of 1 mm
cable must be fully unwound.
• Whenever possible, use a device to block the part
being worked on in position to prevent it from slipping.
• If there is a jam, stop the machine immediately
and unplug it from the mains. Do not start work
again until you have removed the cause of the jam;
if is caused by the machine itself, please send it to
an approved technical service.
• Wear safety glasses, hearing protectors and pro-
tective gloves.
• Before cutting into a partition, ceiling or floor,
make sure these do not contain any ducting.
• Before you use an accessory, make sure that its
maximum rotation speed is compatible with the
machine performance.
• E lectric tools must not be used by under 16 year
olds.
• Do not cut into nails, screws, etc.
• Apply the machine to the material only after it has
been switched on.
• T he cutting path must be free of obstacles on the
top and the bottom.
• Do not stick fingers in the sawdust ejector.
• Keep hand away from the rotating saw blade.
• Do not work overhead with the machine.
• Do not work with materials containing asbestos.
• Do not use a cracked or deformed circular saw
blade or one with missing or broken teeth.
• Do not use saw blades that have a thicker body
or the teeth is smaller than the thickness of the
kerf guide.
• T he kerf guide has to be adjusted in case different
diameters of saw blade are used.
• Do not stop the saw blade after switching off with
side pressure.
• Never block the lower protective housing in the top
position; make sure that it always pivots freely.
• Never use circular saw blade made of high speed
steel (HSS).
• Always use the kerf guide.
• Never force a machine which seems to be labouring
or losing power; there may be a technical problem,
in which case continuing work could damage the
machine irrevocably. Whenever the machine does
not work properly, call an approved agent imme-
diately for a check. It may be advisable to tell the
technical agent or his representative why you are
calling him. T his particularly applies in the case of
intermittent faults.
• Use only original parts and accessories.
2. SPECIFICATION S
2
and the
Mot or.............................................................50/60Hz
Imput power......................................................1200 W
No-load speed.................................................5000/min
Saw diameter.....................................................153 mm
Depth of cut at 90°.............................................51 mm
Depth of cut at 45°...........................................34 mm
Cut separador...........................................................Yes
Weight.......................................................................3,4 Kg
Weighted equivalent continuous acoustic pressure
level A............................................................................98 dBA
Acoustic power level A.................................109 dBA
Uncertainty.............................................................K = 3 dBA
Wear ear protection!
Vibration total values.......................................a
Uncertainty.........................................................K: 1.5 m/s
3. STARTIN G THE MACHIN E
• Switching On - Press the safety button B then press
button A and hold depressed. (Fig. 1)
• Switching Off - Release switch button A.

4. CUTTIN G DEPTH ADJUSTMEN T

Cutting depth can be adjusted by unscrewing tab
top screw (Fig. 6 and 11). Maximum cutting depth
is 50 mm.
5. ADJUSTIN G DIVIDIN G BLADE
T he dividing blade must be adjusted manually when
changing the cutting depth. (Fig. 7)
2
: <2.5 m/s
h
2