Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Direct Wire,
Three-wire electrical connection:
Three wire with ground wire: green or bare
wire cut short. Wire is not used. Dryer is
grounded through neutral conductor.
A
1" (25 mm)
of wires
stripped of
to
insulation
disconnect
box
C
Strip 3
1
covering from end of cable.
Shape ends
Strip insulation back 1" (25 mm).
of wires into
If using 3 wire cable with ground
a hook.
wire, cut green or bare wire even
with outer covering.
A.
" (19 mm) conduit connector
3
⁄
4
B. Neutral (white or center)
C. 10-gauge, 3 wire with ground wire in
flexible metallic conduit
Connect Vent
1. Using a 4" (102 mm) clamp, connect vent to exhaust outlet in
dryer. If connecting to existing vent, make sure the vent is
clean. The dryer vent must fit over the dryer exhaust outlet
and inside the exhaust hood. Make sure the vent is secured to
exhaust hood with a 4" (102 mm) clamp.
2. Move dryer into final position. Do not crush or kink vent.
Make sure dryer is level.
Complete Installation
1. With dryer in final position place level on top of the dryer, first
side to side; then front to back. If the dryer is not level, adjust
the legs of the dryer up or down until the dryer is level.
18
Use this method where local codes permit
connecting neutral ground wire to
neutral wire:
5. Loosen or remove the center terminal
6. Place the hooked end of the neutral wire
7. Place the hooked ends of the other
8. Insert tab of the terminal block cover into
Use this method where local codes do
not permit connecting neutral ground
B
wire to neutral wire:
3
1
⁄
" (89 mm)
5. Remove the center terminal block screw.
2
6. Remove the appliance neutral ground wire
⁄
" (89 mm) of outer
2
7. Connect the other wires to outer terminal
8. Insert tab of the terminal block cover into
9. After reattaching the terminal cover,
If codes permit and a separate ground wire is
used, it is recommended that a qualified
electrician determine that the ground path is
adequate.
block screw.
(white or center) of the direct wire cable
under the center screw of the terminal
block (hook facing right). Squeeze
hooked end together. Tighten screw.
direct wire cable wires under the outer
terminal block screws (hook facing right).
Squeeze hooked ends together. Tighten
screws.
slot of the dryer rear panel. Secure cover
with hold-down screw.
from the external ground conductor screw.
Connect the appliance neutral ground wire
and the neutral wire (white or center) of the
direct wire cable under the center, silver-
colored terminal block screw. Tighten
screw.
block screws. Tighten screws.
slot of the dryer rear panel. Secure cover
with hold-down screw.
connect a separate copper ground wire
from the external ground connector screw
to an adequate ground.
2. Plug in dryer or reconnect power.
3. Check dryer operation (some accumulated time may be on
the timer on mechanical timer models due to factory testing).
Push START/RESTART button. Using a high heat cycle (not
the air cycle), let the dryer run for at least five minutes. Dryer
will stop when time is used up. Make sure the dryer turns off.
NOTE: Dryer door must be closed for dryer to operate. When
door is open, dryer stops, but timer continues to run. To
restart dryer, close door and push START/RESTART button.
4. If drying time is too long, make sure lint screen is clean.
5. Now start the dryer and allow it to complete a full heat cycle
(not air cycle) to make sure it is working properly.
A
E
D
A. External ground conductor screw
B. Center terminal block screw
C. Outer terminal block screws
D. Neutral (center wire)
E. Appliance neutral ground wire
A
C
B
F
A. Separate copper ground wire
B. External ground conductor screw
C. Appliance neutral ground wire
D. Center terminal block screw
E. Outer terminal block screws
F. Neutral (center wire)
B
C
D
E
Publicité
Table des Matières
