Texas Handy-Sweep HS700TG Manuel D'utilisation page 12

Box Contents
Figure 1:
A. Machine with upper handle bar mounted
B. Swing handle
C. Mounting hardware for handle bar
D. EnginО Manual anН UsОr's Manual
E. Guard (Set)
F. Rotary brush (set)
Identification of parts
Figure 2:
A. Brush.
B. Support wheel for brush / adjustment of height.
C. Wheels.
D. Lower handle bar.
E. Mounting hardware for upper part of handle
bar. Adjustment of handle bar.
F. Upper handle bar.
G. Clutch lever - Reverse and forward.
H. Clutch lever - Activating brush.
I. Throttle Lever.
J. Swing handle
K. Engine (may vary from picture)
L. Belt guard
M. Electric starter - 230V (HS700TGE only)
Assembly
The sweeper is almost ready assembled from the
factory. Only a few items remain to be assembled:
1.
Mount upper part of handle bar to lower part
with the enclosed bolt kit. See figure 3
Explanation to figure 3:
A. Lower handle bar
B. Upper handle bar
C. Holder ( Bolt set)
2.
Mount swing handle with enclosed bolt and
nut. Figure 2, J.
3.
Mount the brush on each side following the
assembling method 1 or method 2. See figure
4 (M1 or M2)
Explanation to figure 4, A1:
A. Brush
B. Spacer cup
C. Bracket
D. Bolt
4.
Mount the guard using the enclosed bolt,
washer and nut. Follow the step 1-5 in figure 5.
NB: The sideguards has to be mounted under
the main guard.
Check the tire pressure on both wheels before
use. Correct tire pressure is
30 psi/2 bar. Figure 6.
Use of machine with too low tire pressure,
can damage the tires!
Operation
Read the instruction manual for the engine,
before use
Before using the machine, remove all foreign objects
from the vicinity. Stones, glass, branches and similar
items can damage the sweeping machine. Also check
that all bolts are tightened.
Control oil level before starting the engine.
See attached guide
Start the engine:
1. Open the fuel tap.
2. On a cold engine open the choker.
Note: By a hot engine choke is not required.
3. Turn thО throttlО МablО to "start" position.
4. Pull the recoil starter gently until you feel
resistance in the rope. Then pull quickly and
energetic. Do not at any time let go of the
recoil starter but glide it gently back and pull
again.
5. For 230V electric starter. (HS700TGE only)
Plug the cord into electrical outlet and press
the start button. After the engine is started
remove the plug from the socket alternatively
pull the recoil starter to crank the engine.
6. Regulate the choker until the engine is running
smoothly.
Stop the engine:
1. Set the throttle to minimum gas.
2. Turn the fuel tap to the"oПП" position.
Clutch Lever A - Forward and Reverse.
To operate the black clutch lever A in Fig. 7, the
control stick must first be activated. By tilting the
control stick to the right or left side and then activate
the black handle, the sweeper will move forward or
backwards. To change direction release the lever and
set control stick to the new desired direction and
activate the lever.
Pay attention while reversing. It is important that the
area is cleared, for any obstacle before reversing.
Never reverse the sweeper against a wall, tree or any
other fixed obstacle.
Clutch Lever B - Activation of brush.
To operate the black brush lever in Fig. 7, the control
stick must first be activated. By tilting the red stick
completely to the right and then push the lever down
activates the brush.
The sweeper is equipped with a "dead man's handle",
once released the brush and drive will stop
immediately.
Operation safety zone
Do not leave the operation safety zone marked in fig 9,
while working with the machine. If it is necessary to
leave the operation zone, for example to readjust the
rotary brush or to attach an accessory, first stop the
engine.
11