Publicité
Les langues disponibles
Les langues disponibles
EN
User Manual
E27 lamp socket with sound & light sensor
1
Safety Instructions
1.1
General
•
Read the user manual completely and carefully before use.
The user manual is part of the product and contains important
information for correct use.
•
Keep this user manual.
The user manual must be available for uncertainties and passing the
product.
Risk of electric shock
•
Do not open the housing.
•
Do not modify product and accessories.
•
Do not short connectors and circuits.
•
Use product, product parts and accessories only in perfect
condition.
A defective device may not be put into operation, but must be discon-
nected from mains and protected against further use.
•
In case of questions, defects, mechanical damage, trouble and
other problems, non-recoverable by the documentation, contact
your dealer or producer.
Target group information
Not meant for children.
•
Secure packaging, small parts and insulation against acciden tal
use.
•
Handle the product carefully.
It will be damaged by blows, knocks or a fall from even a short height.
•
Avoid stresses such as heat and cold, moisture and direct sunlight
vibration and mechanical pressure.
•
Do not immerse the product in liquids and protect it from splashing
water.
1.2 Warning levels
Warnings against hazards that may result in injuries in case of
nonobservance.
Warnings against hazards that may result in material damage
in case of non-observance.
2
Description and Function
2.1
Product
The lampholder is equipped with a sound and light sensor and makes it possible
to switch on the lighting at darkness by noises above 60 dB, e.g. voices, clapping,
footsteps, etc. The ideal solution for storerooms, attics, cellars, garages, hallways
and stairwells.
.
2.2
Scope of delivery
E27 lamp socket with sound & light sensor, user manual
2.3
Operating elements and product parts
Fig. 2: Operating elements
1 Lamp socket
3 Sound sensor
2.4
Specifications
Article Number
Operating voltage
Max. power per lamp socket:
Bulb
LED / Energy-saving lamp
Stand-by power consumption
Operating illuminance
Trigger volume
Switch-off delay
Operating temperature range
Socket design
Material
Protection class / protection level
Dimensions (L x Ø)
Weight
Tab. 2: Specifications
REV2018-03-28
V1.0
2 Light sensor
4 Ventilation slots
55500
220-240 @ 50 Hz
V~
60
W
20
W
≤ 0,15
W
≤ 10
Lux
≥ 60
dB
45-50
s
0 ~ 35
°C
E27
ABS, cooper, PBT
II / IP20
103.2 x 54.0
mm
72,0
g
3
Intended Use
We do not permit using the device in other ways like described in chapter
Description and Function. Use the product only in dry interior rooms. Not
attending to these regulations and safety instructions might cause fatal
accidents, injuries, and damages to persons and property.
4
Connecting
Material damage
•
Do not overload the socket with lamps that are too strong!
The wireless lamp socket is designed for a maximum switching capaci-
ty of 60W. See also chapter 2.4 "Specifications".
•
Make sure that the lamp holder is not mounted in the detection
range of another light source, otherwise the built-in light sensor
prevents the light from being switched on.
1.
Compare the specifications of all used devices to ensure compati-
bility
2.
Check the scope of delivery for completeness and integrity.
3.
Switch off the lamp you want to equip with the lamp socket.
4.
Screw the lamp socket directly into the socket of the lamp.
5.
Screw the desired light source into the lamp socket.
6.
Switch on the lamp back again.
The light will turn on as soon as it is dark enough and a noise ≥ 60 dB
sounds.
5
Maintenance, Care, Storage and Transport
The products are maintenance-free.
Material damages
•
Clean only with a dry, soft cloth.
•
Do not use cleaning agents and chemicals.
•
Store cool and dry.
•
Store the product out the reach of children and in a dry and
dust-protected ambience when not in use.
•
Keep and use the original packaging for transport.
6
Liability Notice
•
We reserve the right to printing errors and changes to product,
packaging or product documentation.
•
See our terms of warranty. These are available in their cur-
rent form under the given contact details.
7
Disposal Notes
According to the European WEEE directive, electrical and elect-
ronic equipment must not be disposed with consumers waste.
Its components must be recycled or disposed apart from each
other. Otherwise contaminative and hazardous substances can
pollute our environment.
As a consumer, you are committed by law to dispose electrical
and electronic devices to the producer, the dealer, or public
collecting points at the end of the devices lifetime for free. Parti-
culars are regulated in national right. The symbol on the product,
in the user`s manual, or at the packaging alludes to these terms.
With this kind of waste separation, application, and waste dispo-
sal of used devices you achieve an important share to environ
mental protection.
WEEE No: 82898622
8
EU Declaration of Conformity
With the CE sign Goobay
Wentronic GmbH ensures, that the product is conformed to the
basic standards and directives.
- 2 -
, a registered trademark of the
®
by Wentronic GmbH | Pillmannstraße 12
38112 Braunschweig | Germany
55500
Goobay
®
Publicité
